- 您現在的位置：買賣IC網 > PDF目錄9973 > IDT82V2052EPFG8 (IDT, Integrated Device Technology Inc)IC LIU E1 2CH SHORT HAUL 80-TQFP PDF資料下載
參數資料
| 型號： | IDT82V2052EPFG8 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 10/70頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E1 2CH SHORT HAUL 80-TQFP |
| 標準包裝： | 750 |
| 類型： | 線路接口裝置（LIU） |
| 規程： | E1 |
| 電源電壓： | 3.13 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-TQFP（14x14） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 82V2052EPFG8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
IDT82V2052E
DUAL CHANNEL E1 SHORT HAUL LINE INTERFACE UNIT
FUNCTIONAL DESCRIPTION
18
December 12, 2005
Figure-4 E1 Pulse Template Test Circuit
3.2.3.2 User-Programmable Arbitrary Waveform
When the PULS[3:0] bits are set to ‘11xx’, user-programmable arbitrary
waveform generator mode can be used in the corresponding channel. This
allows the transmitter performance to be tuned for a wide variety of line con-
dition or special application.
Each pulse shape can extend up to 4 UIs (Unit Interval), addressed by
UI[1:0] bits (TCF3, 07H...) and each UI is divided into 16 sub-phases,
addressed by the SAMP[3:0] bits (TCF3, 07H...). The pulse amplitude of
each phase is represented by a binary byte, within the range from +63 to -
63, stored in WDAT[6:0] bits (TCF4, 08H...) in signed magnitude form. The
most positive number +63 (D) represents the maximum positive amplitude
of the transmit pulse while the mostnegative number -63 (D) represents the
maximum negative amplitude of the transmit pulse. Therefore, up to 64
bytes are used. For each channel, a 64 bytes RAM is available.
There are two standard templates which are stored in an on-chip ROM.
User can select one of them as reference and make some changes to get
the desired waveform.
User can change the wave shape and the amplitude to get the desired
pulse shape. In order to do this, firstly, users can choose a set of waveform
value from the following two tables, which is the most similar to the desired
each of the two templates. Then modify the corresponding sample data to
get the desired transmit pulse shape.
Secondly, through the value of SCAL[5:0] bits increased or decreased
by 1, the pulse amplitude can be scaled up or down at the percentage ratio
against the standard pulse amplitude if needed. For different pulse shapes,
the value of SCAL[5:0] bits and the scaling percentage ratio are different.
The following two tables list these values.
Do the followings step by step, the desired waveform can be pro-
grammed, based on the selected waveform template:
(1).Select the UI by UI[1:0] bits (TCF3, 07H...)
(2).Specify the sample address in the selected UI by SAMP [3:0] bits
(TCF3, 07H...)
(3).Write sample data to WDAT[6:0] bits (TCF4, 08H...). It contains the
data to be stored in the RAM, addressed by the selected UI and the
corresponding sample address.
(4).SettheRWbit(TCF3,07H...)to‘0’toimplementwritingdatatoRAM,
or to ‘1’ to implement read data from RAM
(5).Implement the Read from RAM/Write to RAM by setting the DONE
bit (TCF3, 07H...)
Repeat the above steps until all the sample data are written to or read
from the internal RAM.
(6).Write the scaling data to SCAL[5:0] bits (TCF2, 06H...) to scale the
amplitude of the waveform based on the selected standard pulse
amplitude
WhenmorethanoneUIisusedtocomposethepulsetemplate,theover-
lap of two consecutive pulses could make the pulse amplitude overflow
(exceed the maximum limitation) if the pulse amplitude is not set properly.
This overflow is captured by DAC_OV_IS bit (INTS1, 19H...), and, if
enabled by the DAC_OV_IM bit (INTM1, 14H...), an interrupt will be gen-
erated.
IDT82V2052E
VOUT
RLOAD
TTIPn
TRINGn
Note: 1. For RLOAD = 75
(nom), Vout (Peak)=2.37V (nom)
2. For RLOAD =120
(nom), Vout (Peak)=3.00V (nom)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B1N-MW-F4 | CONVERTER MOD DC/DC 18.5V 100W |
| VE-B1N-MW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| V24B48M250BL2 | CONVERTER MOD DC/DC 48V 250W |
| IDT82V2052EPF8 | IC LIU E1 2CH SHORT HAUL 80-TQFP |
| MS3100C22-27S | CONN RCPT 9POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V2054 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:QUAD E1 SHORT HAUL LINE INTERFACE UNIT |
| IDT82V2054BB | 功能描述:IC LIU E1 4CH SHORT HAUL 160-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2054BBG | 功能描述:IC LIU E1 4CH SHORT HAUL 160-BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2054DA | 功能描述:IC LIU E1 4CH SHORT HAUL 144TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2054DAG | 功能描述:IC LIU E1 4CH SHORT HAUL 144TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。