- 您現在的位置：買賣IC網 > PDF目錄9978 > IDT82V2042EPF8 (IDT, Integrated Device Technology Inc)IC LIU T1/J1/E1 2CH SHORT 80TQFP PDF資料下載
參數資料
| 型號： | IDT82V2042EPF8 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 3/83頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/J1/E1 2CH SHORT 80TQFP |
| 標準包裝： | 750 |
| 類型： | 線路接口裝置（LIU） |
| 規程： | E1 |
| 電源電壓： | 3.13 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-TQFP（14x14） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 82V2042EPF8 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
IDT82V2042E
DUAL CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
PIN DESCRIPTION
11
December 12, 2005
RD1/RDP1
RD2/RDP2
CV1/RDN1
CV2/RDN2
O34
26
33
27
RDn: Receive Data output for Channel 1~2
In single rail mode, this pin outputs NRZ data. The data is decoded according to AMI, HDB3 or B8ZS line code rules.
CVn: Code Violation indication
In single rail mode, the BPV/CV errors in received data stream will be reported by driving the CVn pin to high level for a full
clock cycle. B8ZS/HDB3 line code violation can be indicated if the B8ZS/HDB3 decoder is enabled. When AMI decoder is
selected, bipolar violation will be indicated.
In hardware control mode, the EXZ, BPV/CV errors in received data stream are always monitored by the CVn pin if single rail
mode is chosen.
RDPn/RDNn: Positive/Negative Receive Data output for Channel 1~2
In dual rail mode, these pins output the re-timed NRZ data when CDR is enabled, or directly outputs the raw RZ slicer data
if CDR is bypassed.
Active edge and level select:
Data on RDPn/RDNn or RDn is clocked with either the rising or the falling edge of RCLKn. The active polarity is also select-
able. Refer to 3.4.8 RECEIVE PATH SYSTEM INTERFACE for details.
RCLK1
RCLK2
O35
25
RCLKn: Receive Clock output for Channel 1~2
This pin outputs 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode receive clock. Under LOS conditions with AIS enabled
(bit AISE=1), RCLKn is derived from MCLK.
In clock recovery mode, this signal provides the clock recovered from the RTIPn/RRINGn signal. The receive data (RDn in
single rail mode or RDPn and RDNn in dual rail mode) is clocked out of the device on the active edge of RCLKn.
If clock recovery is bypassed, RCLKn is the exclusive OR (XOR) output of the dual rail slicer data RDPn and RDNn. This signal
can be used in applications with external clock recovery circuitry.
MCLK
I
30
MCLK: Master Clock input
A built-in clock system that accepts selectable 2.048 MHz reference for E1 operating mode and 1.544 MHz reference for T1/
J1 operating mode. This reference clock is used to generate several internal reference signals:
Timing reference for the integrated clock recovery unit.
Timing reference for the integrated digital jitter attenuator.
Timing reference for microcontroller interface.
Generation of RCLKn signal during a loss of signal condition.
Reference clock to transmit All Ones, all zeros, PRBS/QRSS pattern as well as activate or deactivate Inband Loop-
back code if MCLK is selected as the reference clock. Note that for ATAO and AIS, MCLK is always used as the refer-
ence clock.
Reference clock during Transmit All Ones (TAO) condition or sending PRBS/QRSS in hardware control mode.
The loss of MCLK will turn TTIP/TRING into high impedance status.
LOS1
LOS2
O32
28
LOSn: Loss of Signal Output for Channel 1~2
These pins are used to indicate the loss of received signals. When LOSn pin becomes high, it indicates the loss of received
signal in channel n. The LOS pin will become low automatically when valid received signal is detected again. The criteria of
loss of signal are described in 3.6 LOS AND AIS DETECTION.
REF
I
71
REF: reference resister
An external resistor (3k
, 1%) is used to connect this pin to ground to provide a standard reference current for internal circuit.
Table-1 Pin Description (Continued)
Name
Type
Pin No.
Description
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B12-MW-F3 | CONVERTER MOD DC/DC 15V 100W |
| VI-212-MX-F3 | CONVERTER MOD DC/DC 15V 75W |
| VI-212-MX-F2 | CONVERTER MOD DC/DC 15V 75W |
| MS27508E12B35SA | CONN RCPT 22POS BOX MNT W/SCKT |
| IDT82V2051EPP | IC LIU E1 SGL SHORT HAUL 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V2042EPFG | 功能描述:IC LIU T1/J1/E1 2CH SHORT 80TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2042EPFG8 | 功能描述:IC LIU T1/J1/E1 2CH SHORT 80TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2044 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:QUAD T1/E1 SHORT HAUL LINE INTERFACE UNIT |
| IDT82V2044BB | 功能描述:IC LIU T1/E1 QUAD SHORT 160-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2044BBG | 功能描述:IC LIU T1/E1 QUAD SHORT 160-BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。