- 您現在的位置：買賣IC網 > PDF目錄360752 > ICS650-27 Networking Clock Source PDF資料下載
參數資料
| 型號： | ICS650-27 |
| 英文描述： | Networking Clock Source |
| 中文描述： | 網絡時鐘源 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 99K |
| 代理商： | ICS650-27 |
Networking Clock Source
MDS 650-27 D
4
Revision 070505
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
●
tel (408) 297-1201
●
www.icst.com
ICS650-27
External Components
The ICS650-27 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
Decoupling capacitors of 0.01μF must be connected
between each VDD and GND (pins 4 and 6, pins 16
and 14), as close to the device as possible. For
optimum device performance, the decoupling capacitor
should be mounted on the component side of the PCB.
Avoid the use of vias in the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance), place a 33
resistor in series
with the clock line as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
Crystal Information
The crystal used should be a fundamental mode (do
not use third overtone), parallel resonant. Crystal
capacitors should be connected from pins X1 to ground
and X2 to ground to optimize the initial accuracy. The
value of these capacitors is given by the following
equation:
Crystal caps (pF) = (C
L
- 6) x 2
In the equation, C
L
is the crystal load capacitance. So,
for a crystal with a 16pF load capacitance, two 20 pF
[(16-6) x 2] capacitors should be used.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS650-27. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
Item
Rating
Supply Voltage, VDD
7 V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
-40 to +85
°
C
-65 to +150
°
C
175
°
C
260
°
C
Ambient Operating Temperature
Storage Temperature
Junction Temperature
Soldering Temperature
Parameter
Min.
Typ.
Max.
Units
°
C
Ambient Operating Temperature
-40
+85
Power Supply Voltage (measured in respect to GND)
+3.0
+3.3
+3.6
V
相關PDF資料 |
PDF描述 |
|---|---|
| ICS650R-27I | Networking Clock Source |
| ICS650R-27ILF | Networking Clock Source |
| ICS650R-27ILFT | Networking Clock Source |
| ICS650R-27IT | Networking Clock Source |
| ICS650-36 | Networking & PCI Clock Source |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS650-36 | 制造商:ICS 制造商全稱:ICS 功能描述:Networking & PCI Clock Source |
| ICS650-40 | 制造商:ICS 制造商全稱:ICS 功能描述:ETHERNET SWITCH CLOCK SOURCE |
| ICS650-40A | 制造商:ICS 制造商全稱:ICS 功能描述:ETHERNET SWITCH CLOCK SOURCE |
| ICS650-41 | 制造商:ICS 制造商全稱:ICS 功能描述:Spread Spectrum Clock Synthesizer |
| ICS650-44 | 制造商:ICS 制造商全稱:ICS 功能描述:Spread Spectrum Clock Synthesizer |
發布緊急采購，3分鐘左右您將得到回復。