- 您現在的位置：買賣IC網 > PDF目錄296200 > HYB39S64160AT-6 (INFINEON TECHNOLOGIES AG) 4M X 16 SYNCHRONOUS DRAM, 5 ns, PDSO54 PDF資料下載
參數資料
| 型號： | HYB39S64160AT-6 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | DRAM |
| 英文描述： | 4M X 16 SYNCHRONOUS DRAM, 5 ns, PDSO54 |
| 封裝： | 10.16 X 22.22 MM, 0.80 MM PITCH, PLASTIC, TSOP2-54 |
| 文件頁數： | 18/18頁 |
| 文件大小： | 118K |
| 代理商： | HYB39S64160AT-6 |
INFINEON Technologies
9
HYB39S6416A/BT-5.5/-6/-7
64MBit Synchronous DRAM
The chip has an on-chip timer and the Self Refresh mode is available. It enters the mode when
RAS, CAS, and CKE are low and WE is high at a clock timing. All of external control signals
including the clock are disabled. Returning CKE to high enables the clock and initiates the refresh
exit operation. After the exit command, at least one tRC delay is required prior to any access
command.
DQM Function
DQM has two functions for data I/O read and write operations. During reads, when it turns to
high“ at a clock timing, data outputs are disabled and become high impedance after two clock delay
(DQM Data Disable Latency tDQZ). It also provides a data mask function for writes. When DQM is
activated, the write operation at the next clock is prohibited (DQM Write Mask Latency tDQW = zero
clocks).
Suspend Mode
During normal access mode, CKE is held high enabling the clock. When CKE is low, it freezes
the internal clock and extends data read and write operations. One clock delay is required for mode
entry and exit (Clock Suspend Latency tCSL).
Power Down
In order to reduce standby power consumption, a power down mode is available. All banks
must be precharged and the necessary Precharge delay (trp) must occur before the SDRAM can
enter the Power Down mode. Once the Power Down mode is initiated by holding CKE low, all of the
receiver circuits except CLK and CKE are gated off. The Power Down mode does not perform any
refresh operations, therefore the device can’t remain in Power Down mode longer than the Refresh
period (tref) of the device. Exit from this mode is performed by taking CKE high“. One clock delay
is required for mode entry and exit.
Auto Precharge
Two methods are available to precharge SDRAMs. In an automatic precharge mode, the CAS
timing accepts one extra address, CA10, to determine whether the chip restores or not after the
operation. If CA10 is high when a Read Command is issued, the Read with Auto-Precharge
function is initiated. The SDRAM automatically enters the precharge operation one clock before the
last data out for CAS latencies 2 and two clocks for CAS latencies 3. If CAS10 is high when a Write
Command is issued, the Write with Auto-Precharge function is initiated. The SDRAM
automatically enters the precharge operation on clock after the last data in.
Precharge Command
There is also a separate precharge command available. When RAS and WE are low and CAS is
high at a clock timing, it triggers the precharge operation. Three address bits, BA0, BA1 and A10 are
used to define banks as shown in the following list. The precharge command can be imposed one
clock before the last data out for CAS latency = 2 and two clocks before the last data out for CAS
latency = 3. Writes require a time delay twr from the last data out to apply the precharge command.
相關PDF資料 |
PDF描述 |
|---|---|
| HYB39T256160TT-5 | MEMORY SPECTRUM |
| HYB39T256160TT-6 | MEMORY SPECTRUM |
| HYB39T256160TT-7 | MEMORY SPECTRUM |
| HYB39T256160TT-75 | MEMORY SPECTRUM |
| HYB39T256160TT-7F | MEMORY SPECTRUM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HYB39S64160AT-7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM |
| HYB39S64160AT-7.5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM |
| HYB39S64160AT-8 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:64 MBit Synchronous DRAM |
| HYB39S64160AT-8B | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:64 MBit Synchronous DRAM |
| HYB39S64160ATL-10 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM |
發布緊急采購，3分鐘左右您將得到回復。