- 您現在的位置：買賣IC網 > PDF目錄370429 > HB28D032MM2 (Hitachi,Ltd.) MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte PDF資料下載
參數資料
| 型號： | HB28D032MM2 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte |
| 中文描述： | 多媒體16 Mbyte/32 Mbyte/64 Mbyte/128字節 |
| 文件頁數： | 54/88頁 |
| 文件大?。?/td> | 329K |
| 代理商： | HB28D032MM2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
HB28E016/D032/D064/B128MM2
54
SPI Communication
The SPI mode consists of a secondary communication protocol. This mode is a subset of the
MultiMediaCard protocol, designed to communicate with a SPI channel, commonly found in Motorola’s
(and lately a few other vendors’) microcontrollers. The interface is selected during the first reset command
after power up (CMD0) and cannot be changed once the part is powered on. The SPI standard defines the
physical link only, and not the complete data transfer protocol. The MultiMediaCard SPI implementation
uses a subset of the MultiMediaCard protocol and command set. It is intended to be used by systems which
require a small number of card (typically one) and have lower data transfer rates (compared to
MultiMediaCard protocol based systems). From the application point of view, the advantage of the SPI
mode is the capability of using an off-the-shelf host, hence reducing the design-in effort to minimum. The
disadvantage is the loss of performance of the SPI system versus MultiMediaCard (lower data transfer rate,
fewer cards, hardware CS per card etc.). While the MultiMediaCard channel is based on command and
data bitstreams which are initiated by a start bit and terminated by a stop bit, the SPI channel is byte
oriented. Every command or data block is built of 8-bit bytes and is byte aligned to the CS signal (i.e. the
length is a multiple of 8 clock cycles). Similar to the MultiMediaCard protocol, the SPI messages consist
of command, response and data-block tokens (refer to Chapter “Commands” and Chapter “Responses” for
a detailed description). All communication between host and cards is controlled by the host (master). The
host starts every bus transaction by asserting the CS signal low. The response behavior in the SPI mode
differs from the MultiMediaCard mode in the following three aspects:
The selected card always responds to the command.
An additional (8 bit) response structure is used
When the card encounters a data retrieval problem, it will respond with an error response (which
replaces the expected data block) rather than by a time-out as in the MultiMediaCard mode.
Single block and multiple read and write operations are supported in SPI mode. In addition to the
command response, every data block sent to the card during write operations will be responded with a
special data response token. A data block may be as big as one card sector and as small as a single byte.
Partial block read/write operations are enabled by card options specified in the CSD register.
Mode Selection
The MultiMediaCard wakes up in the MultiMediaCard mode. It will enter SPI mode if the CS signal is
asserted (negative) during the reception of the reset command (CMD0). Selecting SPI mode is not
restricted to Idle state (the state the card enters after power up) only. Every time the card receives CMD0,
including while in Inactive state, CS signal is sampled.
f the card recognizes that the MultiMediaCard mode is required it will not respond to the command and
remain in the MultiMediaCard mode. If SPI mode is required the card will switch to SPI and respond with
the SPI mode R1 response.
The only way to return to the MultiMediaCard mode is by entering the power cycle. In SPI mode the
MultiMediaCard protocol state machine is not observed. All the MultiMediaCard commands supported in
SPI mode are always available.
相關PDF資料 |
PDF描述 |
|---|---|
| HB28D064MM2 | MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte |
| HB28E016MM2 | MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte |
| HB28C048A6 | FLASH ATA Card |
| HB28C048C6 | CompactFlash⑩ |
| HB28C016A6 | FLASH ATA Card |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB2A102K-S265B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
| HB2A102K-S565B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
| HB2A103K-S565B | 制造商:Hitano Enterprise Corp 功能描述: |
| HB2A122K-S265B | 制造商:Hitano Enterprise Corp 功能描述: |
| HB2A122K-S565B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。