- 您現在的位置：買賣IC網 > PDF目錄362802 > EVAL-AD7933CB (Analog Devices, Inc.) 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer PDF資料下載
參數資料
| 型號： | EVAL-AD7933CB |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | ADC |
| 英文描述： | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| 中文描述： | 4通道，1.5 MSPS的12位和10位并行ADC的一個序列 |
| 文件頁數： | 10/32頁 |
| 文件大?。?/td> | 1253K |
| 代理商： | EVAL-AD7933CB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7933/AD7934
Preliminary Technical Data
Pin No.
20
21
Mnemonic
WR
RD
Description
Write Input. Active low logic input used in conjunction with CS to write data to the control register.
Read Input. Active low logic input used in conjunction with CS to access the conversion result. The conversion
result is placed on the data bus following the falling edge of RD read while CS is low.
Chip Select. Active low logic input used in conjunction with RD and WR to read conversion data or write data to
the control register.
Analog Ground. This is the ground reference point for all analog circuitry on the AD7933/AD7934. All analog
input signals and any external reference signal should be referred to this AGND voltage. The AGND and DGND
voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient
basis.
Reference Input/Output. This pin is connected to the internal reference and is the reference source for the ADC.
The nominal internal reference voltage is 2.5 V and this appears at this pin. This pin can be overdriven by an
external reference. The input voltage range for the external reference is 0.1 V to 3.5 V for differential mode and
is 0.1 V to V
DD
in single-ended and pseudo-differential mode, depending on V
DD
.
Analog Input 0 to Analog Input 3. Four analog input channels that are multiplexed into the on-chip track-and-
hold. The analog inputs can be programmed to be four single ended inputs, two fully differential pairs or two
pseudo-differential pairs by setting the MODE bits in the control register appropriately (see Table 9). The
analog input channel to be converted can either be selected by writing to the address bits (ADD1 and ADD0) in
the control register prior to the conversion, or the on-chip sequencer can be used. The input range for all input
channels can either be 0 V to V
REF
or 0 V to 2 × V
REF
and the coding can be binary or twos complement,
depending on the states of the RANGE and CODING bits in the control register. Any unsed input channels
should be connected to AGND to avoid noise pickup.
22
CS
23
AGND
24
V
REFIN
/V
REFOUT
25 to 28
V
IN
0 to V
IN
3
Rev. PrG | Page 10 of 32
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7934CB | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| EVAL-CONTROLBRD2 | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| EVAL-AD7940CB | 3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
| EVAL-AD974CB | AD974 4-Channel, 16-Bit, 200 kSPS ADC(四通道,200kSPS,16位A/D轉換器,AD974的評估板) |
| EVAL-AD9831EB | CMOS Complete DDS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7934-6CB | 制造商:Analog Devices 功能描述:EVAL BD 4-CH, 1.5 MSPS, 10-BIT AND 12-BIT PARALLEL ADCS W/ A - Bulk |
| EVAL-AD7934CB | 制造商:Analog Devices 功能描述:Evaluation Board For 4-Channel, 1.5 MSPS, 10-Bit And 12-Bit Parallel ADCs With A Sequencer 制造商:Analog Devices 功能描述:EVAL BD 4-CH, 1.5 MSPS, 10-BIT AND 12-BIT PARALLEL ADCS W/ A - Bulk |
| EVAL-AD7938-6CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 625 kSPS, 12-Bit Parallel ADCs with a Sequencer |
| EVAL-AD7938-6CBZ | 制造商:Analog Devices 功能描述:EVAL KIT FOR 8CH, 625 KSPS, 12-BIT PARALLEL ADCS W/ A SEQUEN - Bulk |
| EVAL-AD7938CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
發布緊急采購，3分鐘左右您將得到回復。