參數資料
型號： DS3112N
廠商： Maxim Integrated Products
文件頁數： 132/133頁
文件大?。?/td> 0K
描述： IC MUX TEMPE T3/E3 IND 256-BGA
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 40
控制器類型： 調幀器，多路復用器
接口： 并行/串行
電源電壓： 3.135 V ~ 3.465 V
電流 - 電源： 150mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 256-LBGA
供應商設備封裝： 256-PBGA（27x27）
包裝： 管件
DS3112
98 of 133
10.2 FEAC Status Register Description
Register Name:
FSR
Register Description:
FEAC Status Register
Register Address:
92h
Bit #
7
6
5
4
3
2
1
0
Name
—
RFI
RFCD
Default
—
Bit #
15
14
13
12
11
10
9
8
Name
RFFO
RFFE
RFF5
RFF4
RFF3
RFF2
RFF1
RFF0
Default
—
Note: Bits that are underlined are read-only; all other bits are read-write.
Bit 0: Receive FEAC Codeword Detected (RFCD). This latched read-only event-status bit will be set to a one
each time the FEAC controller has detected and validated a new FEAC codeword. This bit will be cleared when
read and will not be set again until another new codeword is detected. The setting of this bit can cause a hardware
interrupt to occur if the FEAC bit in the Interrupt Mask for MSR (IMSR) register is set to a one. The interrupt will
be allowed to clear when this bit is read.
Bit 14: Receive FEAC FIFO Empty (RFFE). This read-only real time status bit will be set to a one when the
Receive FEAC FIFO is empty and hence the RFF0 to RFF5 bits contain no valid information.
Bit 1: Receive FEAC Idle (RFI). This latched read-only event status bit will be set to a one each time the FEAC
controller has detected 16 consecutive ones following a valid codeword. This bit will be cleared when read. The
setting of this bit can cause a hardware interrupt to occur if the IERFI bit in the FEAC Control Register (FCR) is
set to one and the FEAC bit in the Interrupt Mask for MSR (IMSR) is set to one.
Bits 8 to 13: Receive FEAC FIFO Data (RFF0 to RFF5). Data from the Receive FEAC FIFO can be read from
these bits. The FEAC codeword is of the form ...0xxxxxx011111111... where the rightmost bit is received first.
These six bits are the debounced and integrated middle six bits of the second byte of the FEAC codeword (i.e., the
six “x” bits). RFF0 is the LSB and is received first while RFF5 is the MSB and is received last.
Bit 15: Receive FEAC FIFO Overflow (RFFO). This latched read-only event-status bit will be set to a one when
the receive FEAC controller has attempted to write to an already full Receive FEAC FIFO and current incoming
FEAC codeword is lost. This bit will be cleared when read and will not be set again until another FIFO overflow
occurs (i.e., the Receive FEAC FIFO has been read and then fills beyond capacity).
相關PDF資料
PDF描述
CONREVSMA002-SMD CONN RP-SMA FEMALE R-A SMD
DS21FT44N IC FRAMER E1 4X3 12CH IND 300BGA
PIC16F1933-E/SP MCU 8BIT 4K FLASH 28-DIP
DS21FF42+ IC FRAMER T1 4X4 16CH 300-BGA
CONREVMCX002-L CONN RPMCX FEMALE R/A PCB MT EXT
相關代理商/技術參數
參數描述
DS3112N+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112N+W 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112NC1 制造商:Maxim Integrated Products 功能描述:T3 E3 MULTIPLEXER, 3.3V T3/E3 FRAMER AND M13/E13/G.747 MUX - Rail/Tube
DS3112ND1E 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS3112RD 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*