- 您現在的位置：買賣IC網 > PDF目錄11589 > DS2482S-100+T&R (Maxim Integrated Products)IC I2C TO 1WIRE BRIDGE 8SOIC PDF資料下載
參數資料
| 型號： | DS2482S-100+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I2C TO 1WIRE BRIDGE 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | DS2482S-100+T&RDKR |
Single-Channel 1-Wire Master
Write Configuration
Command Code
D2h
Command Parameter
Configuration Byte
Description
Writes a new configuration byte. The new settings take effect immediately. Note: When writing to
the Configuration Register, the new data is accepted only if the upper nibble (bits 7 to 4) is the
one’s complement of the lower nibble (bits 3 to 0). When read, the upper nibble is always 0h.
Typical Use
Defining the features for subsequent 1-Wire communication.
Restriction
1-Wire activity must have ended before the DS2482-100 can process this command.
Error Response
Command code and parameter are not acknowledged if 1WB = 1 at the time the command code
is received and the command is ignored.
Command Duration
None. The Configuration Register is updated on the rising SCL edge of the configuration-byte
acknowledge bit.
1-Wire Activity
None
Read Pointer Position
Configuration Register (to verify write).
Status Bits Affected
RST set to 0.
Configuration Bits Affected
1WS, SPU, APU updated.
1-Wire Reset
Command Code
B4h
Command Parameter
None
Description
Generates a 1-Wire reset/presence-detect cycle (Figure 4) at the 1-Wire line. The state of the
1-Wire line is sampled at tSI and tMSP and the result is reported to the host processor through the
Status Register, bits PPD and SD.
Typical Use
To initiate or end any 1-Wire communication sequence.
Restriction
1-Wire activity must have ended before the DS2482-100 can process this command. Strong
pullup (see the SPU bit) should not be used in conjunction with the 1-Wire Reset command. If SPU
is enabled, the PPD bit may not be valid and may cause a violation of the device’s absolute
maximum rating.
Error Response
Command code is not acknowledged if 1WB = 1 at the time the command code is received and
the command is ignored.
Command Duration
tRSTL + tRSTH + maximum 262.5ns, counted from the falling SCL edge of the command code
acknowledge bit.
1-Wire Activity
Begins maximum 262.5ns after the falling SCL edge of the command code acknowledge bit.
Read Pointer Position
Status Register (for busy polling).
Status Bits Affected
1WB (set to 1 for tRSTL + tRSTH), PPD is updated at tRSTL + tMSP, SD is updated at tRSTL + tSI.
Configuration Bits Affected
1WS, APU, SPU apply.
DS2482-100
10
Maxim Integrated
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12F629T-I/MD | IC PIC MCU FLASH 1KX14 8DFN |
| PIC24F04KA201-I/SO | IC PIC MCU FLASH 512KX4 20-SOIC |
| PIC16F722-I/MV | IC MCU 8BIT 3.5KB FLASH 28UQFN |
| PIC16F616-I/ST | IC PIC MCU FLASH 2KX14 14TSSOP |
| PIC16F687-E/SS | IC PIC MCU FLASH 2KX14 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2482S-101+ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
| DS2482S-101+TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
| DS2482S-800 | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2482S-800/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2482S-800+ | 功能描述:接口 - 專用 8 Ch 1-Wire Master RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。