Control Functi" />
參數資料
型號： DS2408S+T&R
廠商： Maxim Integrated Products
文件頁數： 8/39頁
文件大?。?/td> 0K
描述： IC SWITCH 8-CHAN ADDRESS 16SOIC
標準包裝： 2,500
接口： 1 線
輸入/輸出數： 8
中斷輸出： *
電源電壓： 2.8 V ~ 5.25 V
工作溫度： *
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 16-SOIC
包裝： 帶卷 (TR)
包括： *
DS2408
16 of 39
CONTROL FUNCTION COMMANDS
Once a ROM function command is completed, the Control Function Commands can be issued. The
Control Functions Flow Chart (Figure 8) describes the protocols necessary for accessing the PIO
channels and the special function registers of the DS2408. The communication between the master and
the DS2408 takes place either at standard speed (default, OD = 0) or at overdrive speed (OD = 1). If not
explicitly set into the overdrive mode, the device operates at standard speed.
Read PIO Registers [F0h]
The Read PIO Registers command is used to read any of the device's registers. After issuing the
command, the master must provide the 2-byte target address. After these two bytes, the master reads data
beginning from the target address and may continue until address 008Fh. If the master continues reading,
it will receive an inverted 16-bit CRC of the command, address bytes, and all data bytes read from the
initial starting byte through the end of the register page. This CRC16 is the result of clearing the CRC
generator and then shifting in the command byte followed by the two address bytes and the data bytes
beginning at the first addressed location and continuing through to the last byte of the register page. After
the bus master has received the CRC16, the DS2408 responds to any subsequent read-time slots with
logical 1’s until a 1-Wire Reset command is issued. If this command is issued with target address 0088h
(PIO Logic State Register), the PIO sampling takes place during the transmission of the MS bit of TA2. If
the target address is lower than 0088h, the sampling takes place while the master reads the MS bit from
address 0087h.
Channel-Access Read [F5h]
In contrast to reading the PIO logical state from address 88h, this command reads the status in an endless
loop. After 32 bytes of PIO pin status the DS2408 inserts an inverted CRC16 into the data stream, which
allows the master to verify whether the data was received error-free. A Channel-Access Read can be
terminated at any time with a 1-Wire Reset.
Figure 9. CHANNEL-ACCESS READ TIMING
IO (1-Wire)
STRB\
Example - Sampled State = 72h
MS 2 bits of pre-
vious byte (8Dh)
LS 2 bits of data
byte (72h)
tSPD
Sampling Point
Notes:
1) The "previous byte" could be the command code, the data byte resulting from the previous PIO
sample, or the MS byte of a CRC16. The example shows a read-1 time slot.
2) The sample point timing also applies to the Channel-access Write command, with the "previous byte"
being the write confirmation byte (AAh). No STRB pulse results when sampling occurs during a
Channel-Access Write command.
相關PDF資料
PDF描述
DS2409P/T&R IC COUPLER MICROLAN 1-WIRE 6TSOC
DS2411P+T&R IC SILICON SERIAL NUMBER 6TSOC
DS2413Q+T&R IC SWITCH 2CH ADDRESS 6-TDFN
DS2480B+ IC LINE DRVR W/SENSOR 1-W 8-SOIC
DS2482X-100+T IC MASTER I2C-1WIRE 1CH 9-WLP
相關代理商/技術參數
參數描述
DS2409 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:MicroLAN Coupler
DS2409FRAB0 制造商:Thomas & Betts 功能描述:200A,REC,3P4W,MG,3P220V,SC
DS2409MP000 制造商:Thomas & Betts 功能描述:200A,PLG,3P4W,MG,409,3P220V
DS2409P 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS2409P/T&R 制造商:Maxim Integrated Products 功能描述:IC COUPLER MICROLAN 1-WIRE 6TSOC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*