- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2408S+T&R (Maxim Integrated Products)IC SWITCH 8-CHAN ADDRESS 16SOIC PDF資料下載
參數資料
| 型號： | DS2408S+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 29/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH 8-CHAN ADDRESS 16SOIC |
| 標準包裝： | 2,500 |
| 接口： | 1 線 |
| 輸入/輸出數： | 8 |
| 中斷輸出： | * |
| 電源電壓： | 2.8 V ~ 5.25 V |
| 工作溫度： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
| 包括： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
DS2408
35 of 39
MASTER MODE
DATA (LSB FIRST)
COMMENTS
TX
04h
Write byte to Control/Status Register
TX
(Reset)
Reset pulse
RX
(Presence)
Presence pulse
Step 2
TX
CCh
Issue Skip ROM command
TX
F0h
Issue Read PIO Registers command
TX
8Dh
TA1, target address = 8Dh
TX
00h
TA2, target address = 008Dh
RX
84h
Read Control/Status Register and verify
TX
(Reset)
Reset pulse
RX
(Presence)
Presence pulse
Step 3
TX
CCh
Issue Skip ROM command
TX
F5h
Issue Channel-access Read command
(—)
DS2408 samples PIO pin status
RX
<PIO pin status byte>
Read PIO pin status
(—)
Repeat the previous 2 steps until the master
has received a total of 32 bytes of PIO pin
status
RX
<2 bytes CRC16>
Read CRC16
(—)
PIO pin status and CRC loop can be
continued as long as the application requires.
TX
(Reset)
Reset pulse
RX
(Presence)
Presence pulse
When using this communication example to read data from a remote microcontroller, as in Figure 17,
synchronization between the remote microcontroller and the master can be maintained by transmitting
data packets that begin with a length byte and end with a CRC16. See Application Note 114, section
"UNIVERSAL DATA PACKET" for details.
Example 3
Task: Detect the specific DS2408 where the button was pressed and identify the pin to which the
pushbutton is connected. This task is broken into the following steps:
1) Configure the conditional search and verify configuration setting.
2) Switch off all channel output transistors.
3) Clear the activity latches.
4) Search until a pushbutton is pressed.
5) Identify device and pushbutton; reset activity latches.
The device has to respond to the conditional search if the activity latch of at least one of the 8 channels is
set. This requires the following setup data for the conditional search registers:
Channel Selection Mask, select all channels FFh
Channel Polarity Selection, select logic 1 for all channels FFh
相關PDF資料 |
PDF描述 |
|---|---|
| DS2409P/T&R | IC COUPLER MICROLAN 1-WIRE 6TSOC |
| DS2411P+T&R | IC SILICON SERIAL NUMBER 6TSOC |
| DS2413Q+T&R | IC SWITCH 2CH ADDRESS 6-TDFN |
| DS2480B+ | IC LINE DRVR W/SENSOR 1-W 8-SOIC |
| DS2482X-100+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2409 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:MicroLAN Coupler |
| DS2409FRAB0 | 制造商:Thomas & Betts 功能描述:200A,REC,3P4W,MG,3P220V,SC |
| DS2409MP000 | 制造商:Thomas & Betts 功能描述:200A,PLG,3P4W,MG,409,3P220V |
| DS2409P | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2409P/T&R | 制造商:Maxim Integrated Products 功能描述:IC COUPLER MICROLAN 1-WIRE 6TSOC |
發布緊急采購，3分鐘左右您將得到回復。