參數資料
型號： DS21Q42T
廠商： DALLAS SEMICONDUCTOR
元件分類： Digital Transmission Controller
英文描述： DATACOM, FRAMER, PQFP128
封裝： TQFP-128
文件頁數： 80/119頁
文件大?。?/td> 1309K
代理商： DS21Q42T
DS21Q42
63 of 119
Transmit a HDLC Message
1. Make sure HDLC controller is done sending any previous messages and is current sending flags by
checking that the FIFO is empty by reading the TEMPTY status bit in the THIR register
2. Enable either the THALF or TNF interrupt
3. Read THIR to obtain TFULL status a. if TFULL=0, then write a byte into the FIFO and skip to next
step (special case occurs when the last byte is to be written, in this case set TEOM=1 before writing
the byte and then skip to step 6) b. if TFULL=1, then skip to step 5
4. Repeat step 3
5. Wait for interrupt, skip to step 3
6. Disable THALF or TNF interrupt and enable TMEND interrupt
7. Wait for an interrupt, then read TUDR status bit to make sure packet was transmitted correctly.
Transmit a BOC
1. Write 6–bit code into TBOC
2. Set SBOC bit in TBOC=1
15.1.3 HDLC/BOC Register Description
HCR: HDLC CONTROL REGISTER (Address = 00 Hex)
(MSB)
(LSB)
RBR
RHR
TFS
THR
TABT
TEOM
TZSD
TCRCD
SYMBOL
POSITION
NAME AND DESCRIPTION
RBR
HCR.7
Receive BOC Reset. A 0 to 1 transition will reset the BOC
circuitry. Must be cleared and set again for a subsequent reset.
RHR
HCR.6
Receive HDLC Reset. A 0 to 1 transition will reset the HDLC
controller. Must be cleared and set again for a subsequent reset.
TFS
HCR.5
Transmit Flag/Idle Select.
0 = 7Eh
1 = FFh
THR
HCR.4
Transmit HDLC/BOC Reset. A 0 to 1 transition will reset
both the HDLC controller and the transmit BOC circuitry. Must
be cleared and set again for a subsequent reset.
TABT
HCR.3
Transmit Abort. A 0 to 1 transition will cause the FIFO
contents to be dumped and one FEh abort to be sent followed
by 7Eh or FFh flags/idle until a new packet is initiated by
writing new data into the FIFO. Must be cleared and set again
for a subsequent abort to be sent.
TEOM
HCR.2
Transmit End of Message. Should be set to a one just before
the last data byte of a HDLC packet is written into the transmit
FIFO at THFR. The HDLC controller will clear this bit when
the last byte has been transmitted.
相關PDF資料
PDF描述
DS21Q43AT DATACOM, FRAMER, PQFP128
DS21Q44T DATACOM, FRAMER, PQFP128
DS21Q44TN DATACOM, FRAMER, PQFP128
DS21Q48N DATACOM, PCM TRANSCEIVER, PBGA144
DS21Q48 DATACOM, PCM TRANSCEIVER, PBGA144
相關代理商/技術參數
參數描述
DS21Q42T+ 功能描述:網絡控制器與處理器 IC Enhanced Quad T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q42TN 功能描述:網絡控制器與處理器 IC Enhanced Quad T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q43A 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Quad E1 Framer
DS21Q43AT 功能描述:網絡控制器與處理器 IC Quad E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q43AT+ 功能描述:網絡控制器與處理器 IC Quad E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*