參數資料
型號： DS2180A
廠商： DALLAS SEMICONDUCTOR
元件分類： 數字傳輸電路
英文描述： T1 Transceiver(T1收發器)
中文描述： DATACOM, FRAMER, PDIP40
封裝： 0.600 INCH, DIP-40
文件頁數： 7/35頁
文件大?。?/td> 232K
代理商： DS2180A
DS2180A
022798 7/35
COMMON CONTROL REGISTER
Figure 4
(MSB)
(LSB)
–
FRSR2
EYELMD
FM
SYELMD
B8ZS
B7
LPBK
SYMBOL
POSITION
NAME AND DESCRIPTION
–
CCR.7
Reserved, must be 0 for proper operation.
FRSR2
CCR.6
Function of REC Status Register 2.
0 = Detected B8ZS code words reported at RSR.2.
1 = COFA (Change-of-Frame Alignment) reported at RSR.2 when last re-
sync resulted in change of frame or multiframe alignment.
EYELMD
CCR.5
193E Yellow Mode Select.
0 = Yellow alarm is a repeating pattern set of 00 hex and FF hex.
1 = Yellow alarm is a 0 in the bit 2 position of all channels.
FM
CCR.4
Frame Mode Select.
0 = D4 (193S, 12 frames/superframe).
1 = Extended (193E, 24 frames/superframe).
SYELMD
CCR.3
193S Yellow Mode Select.
Determines yellow alarm type to be transmitted
and detected while in 193S framing. If set, yellow alarms are a 1 in the S-bit
position of frame 12; if cleared, yellow alarm is a 0 in bit 2 of all channels.
Does not affect 193E yellow alarm operation.
B8ZS
CCR.2
Bipolar eight zero substitution.
0 = No B8ZS.
1 = B8ZS enabled.
(Note: This bit must be set to 0 when CCR.1=1)
B7
CCR.1
Bit seven zero suppression.
If CCR.1=1, channels with an all zero con-
tent will be transmitted with bit 7 forced to 1. If CCR.1=0, no bit 7 stuffing
occurs.
(Note: This bit must be set to 0 when CCR.2=1)
LPBK
CCR.0
Loopback.
When set, the device internally loops output transmit data into
the incoming receive data buffers and TCLK is internally substituted for
RCLK.
LOOPBACK
(Refer to Figure 4)
Enabling loopback will typically induce an out-of-frame
(OOF) condition. If appropriate bits are set in the receive
control register, the receiver will resync to the looped
transmit frame alignment. During the looped condition,
the transmit outputs (TPOS, TNEG) will transmit un-
framed all 1’s. All operating modes (B8ZS, alarm,
signaling, etc.) except for blue alarm transmission are
available in loopback.
BIT SEVEN STUFFING
Existing systems meet 1’s density requirements by forc-
ing bit 7 of all zero channels to 1. Bit 7 stuffing is globally
enabled by asserting bit CCR.1 and may be disabled on
an individual channel basis by setting appropriate bits in
TTR1–TTR3. Bit 7 stuffing and B8ZS modes should not
be enabled simultaneously. Enabling both results in
LOS.
相關PDF資料
PDF描述
DS2187 Receive Line Interface(接收線接口)
DS2250T Soft Microcontroller Module(軟件微控制器模塊)
DS2251T 128K Soft Microcontroller Module(128K軟件微控制器模塊)
DS2252T Secure Microcontroller Module(安全的微控制器模塊)
DS229 Triple RS232 Transmitter/Receiver(三路RS232發送器/接收器)
相關代理商/技術參數
參數描述
DS2180A+ 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AN 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ/T&R 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver
DS2180AQ/T&R+ 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*