- 您現在的位置：買賣IC網 > PDF目錄385273 > DS2180A (DALLAS SEMICONDUCTOR) T1 Transceiver(T1收發器) PDF資料下載
參數資料
| 型號： | DS2180A |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | T1 Transceiver(T1收發器) |
| 中文描述： | DATACOM, FRAMER, PDIP40 |
| 封裝： | 0.600 INCH, DIP-40 |
| 文件頁數： | 21/35頁 |
| 文件大小： | 232K |
| 代理商： | DS2180A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
DS2180A
022798 21/35
RYEL OUTPUT
The yellow alarm output transitions high when a yellow
alarm is detected. A high-low transition indicates the
alarm condition has been cleared. The RYEL bit
(RSR.5) is a “l(fā)atched” version of the RYEL output. In
193E framing, the yellow alarm pattern detected is 16
pattern sets of 00 (Hex) and FF (Hex) received at
RLINK. In 193S, framing the yellow alarm format is de-
pendent on CCR.3; if CCR.3=0, the RYEL output transi-
tions high if bit 2 of 256 or more consecutive channels is
0; if CCR.3=1, yellow alarm is declared when the S-bit
received in frame 12 is 1.
RBV OUTPUT
The bipolar violation output transitions high when an ac-
cused bit emerges at RSER. RBV will go low at the next
bit time if no additional violations are detected.
RFER OUTPUT
The receive frame error output transitions high at the F-
bit time and is held high for two bit periods when a frame
bit error occurs. In 193S framing, F
T
and F
S
patterns are
tested. The FPS pattern is tested in 193E framing. Addi-
tionally, in 193E framing, RFER reports a CRC error by a
low-high-low transition (one bit period wide) one half
RCLK period before a low-high transition on RMSYNC.
RESET
A high-low transition on RST clears all registers and
forces immediate receive resync when RST returns
high. This reset has no effect on transmit frame multi-
frame or channel counters. RST must be held low on
system power-up to insure proper initialization of trans-
ceiver counters and registers. Following reset, the host
processor should restore all control modes by writing
appropriate registers with control data.
ALARM OUTPUT TIMING
Figure 21
RCLK
RFSYNC
RMSYNC
RFER
1
RBV
2
RCL
3
RLOS
4
NOTES:
1. RFER transitions high during F-bit time if received framing pattern bit is in error. (Frame 12 F-bits in 193S are
ignored if CCR.3=1). Also, in 193E, RFER transitions 1/2 bit time before the rising edge of RMSYNC to indi-
cate a CRC error for the previous multiframe.
2. RBV indicates received bipolar violation and transitions high when an accused bit emerges from RSER. If
B8ZS is enabled, RBV will not report the zero replacement code.
3. RCL transitions high (during 32nd bit time) when 32 consecutive bits received are 0; RCL transitions low
when the next 1 is received.
4. RLOS transitions high during the F-bit time that caused an OOF event (any two of four consecutive F
T
or FPS
bits are in error) if auto-resync mode is selected (RCR.1=0). Resync will also occur when loss of carrier is
detected (RCL=1). When RCR.1=1, RLOS remains low until resync occurs, regardless of OOF or carrier loss
flags. In this situation, resync is initiated only when RCR.0 transitions low-to-high or the RST pin transitions
high-low-high.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2187 | Receive Line Interface(接收線接口) |
| DS2250T | Soft Microcontroller Module(軟件微控制器模塊) |
| DS2251T | 128K Soft Microcontroller Module(128K軟件微控制器模塊) |
| DS2252T | Secure Microcontroller Module(安全的微控制器模塊) |
| DS229 | Triple RS232 Transmitter/Receiver(三路RS232發送器/接收器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2180A+ | 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2180AN | 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2180AQ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2180AQ/T&R | 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver |
| DS2180AQ/T&R+ | 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。