- 您現在的位置：買賣IC網 > PDF目錄379182 > DS2154L Enhanced E1 Single Chip Transceiver PDF資料下載
參數資料
| 型號： | DS2154L |
| 英文描述： | Enhanced E1 Single Chip Transceiver |
| 中文描述： | 增強素E1單芯片收發器 |
| 文件頁數： | 65/87頁 |
| 文件大小： | 1106K |
| 代理商： | DS2154L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁
DS2154
65 of 87
12.3 JITTER ATTENUATOR
The DS2154 contains an onboard jitter attenuator that can be set to a depth of either 32 or 128 bits via the
JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications
where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications.
The characteristics of the attenuation are shown in Figure 12-4. The jitter attenuator can be placed in
either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR.
Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA bit in the LICR. In order
for the jitter attenuator to operate properly, a 2.048 MHz clock (
±
50 ppm) must be applied at the MCLK
pin or a crystal with similar characteristics must be applied across the MCLK and XTALD pins. If a
crystal is applied across the MCLK and XTALD pins, then capacitors should be placed from each leg of
the crystal to ground as shown in Figure 12-1. Onboard circuitry adjusts either the recovered clock from
the clock/data recovery block or the clock applied at the TCLKI pin to create a smooth jitter-free clock
which is used to clock data out of the jitter attenuator FIFO. It is acceptable to provide a gapped/bursty
clock at the TCLKI pin if the jitter attenuator is placed on the transmit side. If the incoming jitter exceeds
either 120 UIpp (buffer depth is 128 bits) or 28 UIpp (buffer depth is 32 bits), then the DS2154 will
divide the internal nominal 32.768 MHz clock by either 15 or 17 instead of the normal 16 to keep the
buffer from overflowing. When the device divides by either 15 or 17, it also sets the Jitter Attenuator
Limit Trip (JALT) bit in the Receive Information Register (RIR.5).
DS2154 EXTERNAL ANALOG CONNECTIONS
Figure 12-1
NOTES:
1.
All resistor values are ±1%.
2.
The Rt resistors are used to increase the transmitter return loss or to protect the device from over–
voltage.
3.
The Rr resistors are used to terminate the receive E1 line.
4.
For 75-ohm termination, Rr=37.5 ohms; for 120-ohm termination Rr=60 ohm.
5.
See the separate Application Note for details on how to construct a protected interface.
6.
Either a crystal can be applied across the MCLK and XTALD pins or a TTL level clock can be
applied to just MCLK.
7.
C1 and C2 should be 5 pF lower than two times the nominal loading capacitance of the crystal to
adjust for the input capacitance of the DS2154.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2154LN | Enhanced E1 Single Chip Transceiver |
| DS2154 | WSD 151 SOLDERING STATION 230V UKWSD 151 SOLDERING STATION 230V UK; Frequency, supply max:60Hz; Frequency, supply min:50Hz; Height:101mm; Length:166mm; Power, input:150W; Temperature range:50(degree C) - 550(degree C); Voltage, |
| DS2155 | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
| DS2156 | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
| DS2156L | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2154L+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154L-C01 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS2154LD1 | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。