- 您現在的位置：買賣IC網 > PDF目錄379182 > DS2154L Enhanced E1 Single Chip Transceiver PDF資料下載
參數資料
| 型號： | DS2154L |
| 英文描述： | Enhanced E1 Single Chip Transceiver |
| 中文描述： | 增強素E1單芯片收發器 |
| 文件頁數： | 32/87頁 |
| 文件大?。?/td> | 1106K |
| 代理商： | DS2154L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁
DS2154
32 of 87
4.0 STATUS AND INFORMATION REGISTERS
There is a set of four registers that contain information on the current real time status of the DS2154,
Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Register (RIR), and Synchronizer
Status Register (SSR). When a particular event has occurred (or is occurring), the appropriate bit in one
of these four registers will be set to a 1. All of the bits in these registers operate in a latched fashion
(except for the SSR). This means that if an event or an alarm occurs and a bit is set to a 1 in any of the
registers, it will remain set until the user reads that bit. The bit will be cleared when it is read and it will
not be set again until the event has occurred again (or in the case of the RSA1, RSA0, RDMA, RUA1,
RRA, RCL, and RLOS alarms, the bit will remain set if the alarm is still present).
The user will always precede a read of the SR1, SR2, and RIR registers with a write. The byte written to
the register will inform the DS2154 which bits the user wishes to read and have cleared. The user will
write a byte to one of these three registers, with a 1 in the bit positions he or she wishes to read and a 0 in
the bit positions he or she does not wish to obtain the latest information on. When a 1 is written to a bit
location, the read register will be updated with the latest information. When a 0 is written to a bit
position, the read register will not be updated and the previous value will be held. A write to the status
and information registers will be immediately followed by a read of the same register. The read result
should be logically AND’ed with the mask byte that was just written and this value should be written
back into the same register to insure that bit does indeed clear. This second write step is necessary
because the alarms and events in the status registers occur asynchronously in respect to their access via
the parallel port. This write-read-write scheme allows an external microcontroller or microprocessor to
individually poll certain bits without disturbing the other bits in the register. This operation is key in
controlling the DS2154 with higher-order software languages.
The SSR register operates differently than the other three. It is a read-only register and it reports the status
of the synchronizer in real time. This register is not latched and it is not necessary to precede a read of
this register with a write.
The SR1 and SR2 registers have the unique ability to initiate a hardware interrupt via the
INT
output pin.
Each of the alarms and events in the SR1 and SR2 can be either masked or unmasked from the interrupt
pins via the Interrupt Mask Register 1 (IMR1) and Interrupt Mask Register 2 (IMR2) respectively.
The interrupts caused by RUA1, RRA, RCL, and RLOS act differently than the interrupts caused by
RSA1, RDMA, RSA0, RSLIP, RMF, RAF, TMF, SEC, TAF, LOTC, RCMF, and TSLIP. The four
interrupts will force the
INT
pin low whenever the alarm changes state (i.e., the alarm goes active or
inactive according to the set/ clear criteria in Table 4-1). The
INT
pin will be allowed to return high (if no
other interrupts are present) when the user reads the alarm bit that caused the interrupt to occur If the
alarm is still present, the register bit will remain set.
The event caused interrupts will force the
INT
pin low when the event occurs. The
INT
pin will be
allowed to return high (if no other interrupts are present) when the user reads the event bit that caused the
interrupt to occur.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2154LN | Enhanced E1 Single Chip Transceiver |
| DS2154 | WSD 151 SOLDERING STATION 230V UKWSD 151 SOLDERING STATION 230V UK; Frequency, supply max:60Hz; Frequency, supply min:50Hz; Height:101mm; Length:166mm; Power, input:150W; Temperature range:50(degree C) - 550(degree C); Voltage, |
| DS2155 | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
| DS2156 | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
| DS2156L | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2154L+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154L-C01 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS2154LD1 | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。