- 您現在的位置：買賣IC網 > PDF目錄379182 > DS2154L Enhanced E1 Single Chip Transceiver PDF資料下載
參數資料
| 型號： | DS2154L |
| 英文描述： | Enhanced E1 Single Chip Transceiver |
| 中文描述： | 增強素E1單芯片收發器 |
| 文件頁數： | 20/87頁 |
| 文件大?。?/td> | 1106K |
| 代理商： | DS2154L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁
DS2154
20 of 87
2.0 PARALLEL PORT
The DS2154 is controlled via either a non-multiplexed (MUX=0) or a multiplexed (MUX=1) bus by an
external microcontroller or microprocessor. The DS2154 can operate with either Intel or Motorola bus
timing configurations. If the BTS pin is tied low, Intel timing will be selected; if tied high, Motorola
timing will be selected. All Motorola bus signals are listed in parenthesis (). See the timing diagrams in
the A.C. Electrical Characteristics in Section 14 for more details.
3.0 CONTROL, ID AND TEST REGISTERS
The operation of the DS2154 is configured via a set of nine control registers. Typically, the control
registers are only accessed when the system is first powered up. Once the DS2154 has been initialized,
the control registers will only need to be accessed when there is a change in the system configuration.
There are two Receive Control Registers (RCR1 and RCR2), two Transmit Control Registers (TCR1 and
TCR2), and five Common Control Registers (CCR1 to CCR5). Each of the nine registers is described in
this section.
There is a device IDentification Register (IDR) at address 0FH. The MSB of this read-only register is
fixed to a 1, indicating that the DS2154 is present. The pin-for-pin compatible T1 version of the DS2154
also has an ID register at address 0FH and the user can read the MSB to determine which chip is present
since in the DS2154 the MSB will be set to a 1 and in the DS2152 it will be set to a 0. The lower 4 bits of
the IDR are used to display the die revision of the chip.
The Test Registers at addresses 15, 19, and AC hex are used by the factory in testing the DS2154. On
power-up, the Test Registers should be set to 00 hex in order for the DS2154 to operate properly.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2154LN | Enhanced E1 Single Chip Transceiver |
| DS2154 | WSD 151 SOLDERING STATION 230V UKWSD 151 SOLDERING STATION 230V UK; Frequency, supply max:60Hz; Frequency, supply min:50Hz; Height:101mm; Length:166mm; Power, input:150W; Temperature range:50(degree C) - 550(degree C); Voltage, |
| DS2155 | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
| DS2156 | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
| DS2156L | T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2154L+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154L-C01 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS2154LD1 | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。