- 您現在的位置：買賣IC網 > PDF目錄11005 > DS21354LC1+ (Maxim Integrated Products)IC TXRX E1 3.3V 100-LQFP PDF資料下載
參數資料
| 型號： | DS21354LC1+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 82/124頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX E1 3.3V 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 功能： | 單芯片收發器 |
| 接口： | E1，HDLC |
| 電路數： | 1 |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 電流 - 電源： | 75mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
| 包括： | 遠程和 AIS 警報檢測器 / 發生器 |
| 產品目錄頁面： | 1430 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers
60 of 124
10.
PER-CHANNEL CODE GENERATION AND LOOPBACK
The DS21354/DS21554 can replace data on a channel-by-channel basis in both the transmit and receive
directions. The transmit direction is from the backplane to the E1 line and is covered in Section 10.1. The
receive direction is from the E1 line to the backplane and is covered in Section 10.2.
10.1.
Transmit-Side Code Generation
In the transmit direction there are two methods by which channel data from the backplane can be
overwritten with data generated by the framer. The first method covered in Section 10.1.1 was a feature
contained in the original DS2153, while the second method covered in 10.1.2 is a new feature of the
DS2154/DS21354/DS21554.
10.1.1.
Simple Idle Code Insertion and Per-Channel Loopback
The first method involves using the Transmit Idle Registers (TIR1/2/3/4) to determine which of the 32 E1
channels should be overwritten with the code placed in the Transmit Idle Definition Register (TIDR).
This method allows the same 8-bit code to be placed into any of the 32 E1 channels. If this method is
used, then the CCR3.5 control bit must be set to zero.
Each of the bit position in the Transmit Idle Registers (TIR1/TIR2/TIR3/TIR4) represent a DS0 channel
in the outgoing frame. When these bits are set to a one, the corresponding channel will transmit the Idle
Code contained in the Transmit Idle Definition Register (TIDR).
The Transmit Idle Registers (TIRs) have an alternate function that allow them to define a Per-Channel
Loopback (PCLB). If the TIRFS control bit (CCR3.5) is set to one, then the TIRs determine which
channels (if any) from the backplane should be replaced with the data from the receive side or in other
words, off of the E1 line. If this mode is enabled, then transmit and receive clocks and frame syncs must
be synchronized.
One method to accomplish this would be to tie RCLK to TCLK and RFSYNC to TSYNC. There are no
restrictions on which channels can be looped back or on how many channels can be looped back.
TIR1/TIR2/TIR3: TRANSMIT IDLE REGISTERS (Address = 26 to 29 Hex)
[Also used for Per-Channel Loopback]
(MSB)
(LSB)
CH8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
TIR1 (26)
CH16
CH15
CH14
CH13
CH12
CH11
CH10
CH9
TIR2 (27)
CH24
CH23
CH22
CH21
CH20
CH19
CH18
CH17
TIR3 (28)
CH32
CH31
CH30
CH29
CH28
CH27
CH26
CH25
TIR4 (29)
SYMBOL
POSITION
NAME AND DESCRIPTION
CH1 to
CH32
TIR1.0 to
TIR4.7
Transmit Idle Code Insertion Control Bits.
0 = do not insert the Idle Code in the TIDR into this channel
1 = insert the Idle Code in the TIDR into this channel
Note: If CCR3.5 = 1, then a zero in the TIRs implies that channel data is to be sourced from TSER,
and a one implies that channel data is to be sourced from the output of the receive-side framer (i.e.,
Per-Channel Loopback; see Figure 2-1).
相關PDF資料 |
PDF描述 |
|---|---|
| S9S08SG16E1MTL | MCU 16K FLASH 28-TSSOP |
| MC9S08SL16CTJ | MCU 16KB FLASH SLIC 20TSSOP |
| DS21554LB+ | IC TXRX E1 5V 100-LQFP |
| MC908QY4ACDTER | MCU 8BIT 4K FLASH W/ADC 16-TSSOP |
| MC908QY4CDTER | IC MCU 8BIT 4K FLASH 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21354LC1+ | 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21354LN | 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21354LN+ | 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21372 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3.3V Bit Error Rate Tester BERT |
| DS21372T | 功能描述:網絡控制器與處理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。