參數資料
型號： DS21354LC1+
廠商： Maxim Integrated Products
文件頁數： 110/124頁
文件大?。?/td> 0K
描述： IC TXRX E1 3.3V 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
功能： 單芯片收發器
接口： E1，HDLC
電路數： 1
電源電壓： 3.14 V ~ 3.47 V
電流 - 電源： 75mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
包括： 遠程和 AIS 警報檢測器 / 發生器
產品目錄頁面： 1430 (CN2011-ZH PDF)
DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers
86 of 124
15.4.
Protected Interfaces
In certain applications, such as connecting to the PSTN, it is required that the network interface be
protected from and resistant to certain electrical conditions. These conditions are divided into two
categories, surge and power line cross. A typical cause of surge is lightening strike. Power-line cross
refers to accidental contact with high-voltage power wiring. For protection against surges, additional
components and PC board layout considerations are required to reroute and dissipate this energy. In a
surge event, the network interface must not be damaged and continue to work after the event. In the event
of a power line contact, components such as fuses or PTCs that can “open” the circuit are required to
prevent the possibility of a fire caused by overheating the transformer. The circuit examples in this data
sheet are for “Secondary Over Voltage Protection” schemes for the line terminating equipment. Primary
protection is typically provided by the network service provide and is external to the equipment.
Figure 15-6 shows an example circuit for the 5V device and Figure 15-7 is an example for the 3.3V
device. In both examples, fuses are used to provide protection against power-line cross. Surge protection
is provided by 470
W input resistors on the receive pair, a transient suppresser, and a diode bridge on the
transmit pair. Resistors R1 to R4 provide surge protection for the fuse. Careful selection of the
transformer allows the use of a fuse that requires no additional surge protection such as the circuit shown
in Figure 15-7. The circuit shown in Figure 15-7 is required for 3.3V operation since additional resistance
in the transmit pair cannot be tolerated. For more information on line interface design, consult the E1 Line
Interface Design Criteria and Secondary Overvoltage Protection application notes available on our
相關PDF資料
PDF描述
S9S08SG16E1MTL MCU 16K FLASH 28-TSSOP
MC9S08SL16CTJ MCU 16KB FLASH SLIC 20TSSOP
DS21554LB+ IC TXRX E1 5V 100-LQFP
MC908QY4ACDTER MCU 8BIT 4K FLASH W/ADC 16-TSSOP
MC908QY4CDTER IC MCU 8BIT 4K FLASH 16-TSSOP
相關代理商/技術參數
參數描述
DS21354LC1+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354LN 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354LN+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21372 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3.3V Bit Error Rate Tester BERT
DS21372T 功能描述:網絡控制器與處理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*