參數資料
型號： DS21352LN
廠商： Maxim Integrated Products
文件頁數： 104/137頁
文件大?。?/td> 0K
描述： IC TXRX T1 1-CHIP 3.3V 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
產品變化通告： Product Discontinuation 20/Feb/2012
標準包裝： 90
功能： 單芯片收發器
接口： HDLC，T1
電路數： 1
電源電壓： 3.14 V ~ 3.47 V
電流 - 電源： 75mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
包括： DSX-1 和 CSU 線路補償發生器，HDLC 控制器，帶內回路代碼發生器和檢測器
DS21352/DS21552
69 of 137
Like the SR1 and SR2 status registers, the HSR register has the unique ability to initiate a hardware
interrupt via the INT* output pin. Each of the events in the HSR can be either masked or unmasked from
the interrupt pin via the HDLC Interrupt Mask Register (HIMR). Interrupts will force the INT* pin low
when the event occurs. The INT pin will be allowed to return high (if no other interrupts are present)
when the user reads the event bit that caused the interrupt to occur.
15.3.3 BASIC OPERATION DETAILS
To allow the framer to properly source/receive data from/to the HDLC and BOC controller the legacy FDL circuitry (which is
described in Section 15.4) should be disabled and the following bits should be programmed as shown:
TCR1.2 = 1 (source FDL data from the HDLC and BOC controller)
TBOC.6 = 1 (enable HDLC and BOC controller)
CCR2.5 = 0 (disable SLC–96 and D4 Fs–bit insertion)
CCR2.4 = 0 (disable legacy FDL zero stuffer)
CCR2.1 = 0 (disable SLC–96 reception)
CCR2.0 = 0 (disable legacy FDL zero stuffer)
IMR2.4 = 0 (disable legacy receive FDL buffer full interrupt)
IMR2.3 = 0 (disable legacy transmit FDL buffer empty interrupt)
IMR2.2 = 0 (disable legacy FDL match interrupt)
IMR2.1 = 0 (disable legacy FDL abort interrupt).
As a basic guideline for interpreting and sending both HDLC messages and BOC messages, the following sequences can be
applied:
15.3.3.1 RECEIVE AN HDLC MESSAGE OR A BOC
1) Enable RBOC and RPS interrupts.
2) Wait for interrupt to occur.
3) If RBOC=1, then follow steps 5 and 6.
4) If RPS=1, then follow steps 7 through 13.
5) If LBD=1, a BOC is present, then read the code from the RBOC register and take action as needed.
6) If BD=0, a BOC has ceased, take action as needed and then return to step 1.
7) Disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt.
8) Read RHIR to obtain REMPTY status.
a) If REMPTY=0, then record OBYTE, CBYTE, and POK bits and then read the FIFO.
i)
If CBYTE=0 then skip to step 9.
ii) If CBYTE=1 then skip to step 11.
b) If REMPTY=1, then skip to step 10.
9) Repeat step 8.
10) Wait for interrupt, skip to step 8.
11) If POK=0, then discard whole packet.
12) If POK=1, accept the packet.
13) Disable RPE, RNE, or RHALF interrupt, enable RPS interrupt and return to step 1.
相關PDF資料
PDF描述
S9S08DZ32F1CLH MCU 32K FLASH AUTO 64-LQFP
S9S08DZ32F1MLC MCU 32K FLASH MASK AUTO 32-LQFP
DS21352L IC TXRX T1 1-CHIP 3.3V 100-LQFP
VI-B5K-IY-F1 CONVERTER MOD DC/DC 40V 50W
DS21554L IC TXRX E1 1-CHIP 5V 100-LQFP
相關代理商/技術參數
參數描述
DS21352LN+ 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.3V/5V E1 Single-Chip Transceivers
DS21354DK 功能描述:網絡開發工具 DS21354 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
DS21354G 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354GN 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*