參數資料
型號： DS1920
廠商： Maxim Integrated Products, Inc.
英文描述： Temperature Button(溫度按鈕)
文件頁數： 11/52頁
文件大?。?/td> 881K
代理商： DS1920
AD14160/AD14160L
–11–
REV. A
Pin
Type
I/O/T
2
Function
BMSBCD
Boot Memory Select.
Output:
Used as chip select for boot EPROM devices (when EBOOTBCD = 1,
LBOOTBCD = 0). In a multiprocessor system, BMS is output by the bus master.
Input:
When low,
indicates that no booting will occur and that SHARC_B, C, D will begin executing instructions from
external memory. See table below. This input is a system configuration selection which should be
hardwired.
EBOOT
LBOOT
BMS
Booting Mode
1
0
Output
EPROM (Connect BMS to EPROM chip select)
0
0
1 (Input)
Host Processor
0
1
1 (Input)
Link Port
0
0
0 (Input)
No Booting. Processor executes from external memory.
0
1
0 (Input)
Reserved
1
1
x (Input)
Reserved
Timer Expired.
(Individual TIMEXP from y = SHARC_A, SHARC_B, SHARC_C, SHARC_D) Asserted
for four cycles when the timer is enabled and TCOUNT decrements to zero.
Clock In.
(Common to all SHARCs) External clock input to the AD14160/AD14160L. The instruction
cycle rate is equal to CLKIN. CLKIN may not be halted, changed, or operated below the minimum specified
frequency.
Module Reset.
(Common to all SHARCs) Resets the AD14160/AD14160L to a known state. This input
must be asserted (low) at power-up.
Test Clock (JTAG).
(Common to all SHARCs) Provides an asynchronous clock for JTAG boundary
scan.
Test Mode Select (JTAG).
(Common to all SHARCs) Used to control the test state machine. TMS has
a 20 k
internal pull-up resistor.
Test Data Input (JTAG).
Provides serial data for the boundary scan logic chain starting at SHARC_A.
TDI has a 20 k
internal pull-up resistor.
Test Data Output (JTAG).
Serial scan output of the boundary scan chain path, from SHARC_D.
Test Reset (JTAG).
(Common to all SHARCs) Resets the test state machine.
TRST
must be asserted
(pulsed low) after power-up or held low for proper operation of the AD14160/AD14160L.
TRST
has a
20 k
internal pull-up resistor.
Emulation Status.
(Common to all SHARCs) Must be connected to the ADSP-2106x EZ-ICE target
board connector
only
.
Power Supply.
Nominally +5.0 V dc for 5 V devices or +3.3 V dc for 3.3 V devices (50 pins).
Power Supply Return.
(64 pins).
TIMEXPy
O
CLKIN
I
RESET
I/A
TCK
I
TMS
I/S
TDI
I/S
TDO
TRST
O
I/A
EMU
(O/D)
O
V
DD
GND
P
G
NOTES
1
LINK PORTS 0 and 5 are connected internally as described earlier in Link Port I/O.
2
Three-statable only in EPROM boot mode (when
BMS
is an output).
相關PDF資料
PDF描述
DS1962 1K-Bit Monetary iButton(1K位貨幣按鈕)
DS1963 4K-Bit Monetary iButton(4K位貨幣按鈕)
DS1981U UniqueWare iButton(唯一貨品按鈕)
DS1982U UniqueWare iButton(UniqueWare iButton標準的EPROM)
DS1982 UniqueWare iButton(UniqueWare iButton標準的EPROM)
相關代理商/技術參數
參數描述
DS1920+F5 制造商:Maxim Integrated Products 功能描述:TEMP IBTN 2PIN F5 MICROCAN - Rail/Tube
DS1920-F3 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Temperature iButton
DS1920-F5 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated
DS1920-F5+ 功能描述:iButton Temperature iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated
DS1921 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Resolution Thermochron iButton
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*