- 您現在的位置：買賣IC網 > PDF目錄376551 > D80C51 (Intel Corp.) CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | D80C51 |
| 廠商： | Intel Corp. |
| 英文描述： | CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 中文描述： | CHMOS單片8位微控制器 |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 284K |
| 代理商： | D80C51 |
87C51/80C51BH/80C31BH
IDLE MODE
In Idle Mode, the CPU puts itself to sleep while all
the on-chip peripherals remain active. The mode is
invoked by software. The content of the on-chip
RAM and all the Special Functions Registers remain
unchanged during this mode. The Idle Mode can be
terminated by any enabled interrupt or by a hard-
ware reset.
It should be noted that when Idle is terminated by a
hardware reset, the device normally resumes pro-
gram execution, from where it left off, up to two ma-
chine cycles before the internal reset algorithm
takes control. On-chip hardware inhibits access to
internal RAM in this event, but access to the port
pins is not inhibited. To eliminate the possibility of an
unexpected write to a port pin when Idle is terminat-
ed by reset, the instruction following the one that
invokes Idle should not be one that writes to a port
pin or to external memory.
POWER DOWN MODE
To save even more power, a Power Down mode can
be invoked by software. In this mode, the oscillator
is stopped and the instruction that invoked Power
Down is the last instruction executed. The on-chip
RAM and Special Function Registers retain their val-
ues until the Power Down mode is transmitted.
On the 87C51/BH either a hardware reset or an ex-
ternal interrupt can cause an exit from Power Down.
Reset redefines all the SFR’s but does not change
the on-chip RAM. An external interrupt allows both
the SFRs and on-chip RAM to retain their values.
To properly terminate Power Down, the reset or ex-
ternal interrupt should not be executed before V
CC
is
restored to its normal operating level, and must be
held active long enough for the oscillator to restart
and stabilize (normally less than 10 ms).
With an external interrupt INT0 and INT1 must be
enabled and configured as level-sensitive. Holding
the pin low restarts the oscillator but bringing the pin
back high completes the exit. Once the interrupt is
serviced, the next instruction to be executed after
RET1 will be the one following the instruction that
put the device into Power Down.
DESIGN CONSIDERATIONS
#
Exposure to light when the device is in operation
may cause logic errors. For this reason, it is sug-
gested that an opaque label be placed over the
window when the die is exposed to ambient light.
#
The 87C51/BH now have some additional fea-
tures. The features are: asynchronous port reset,
4 interrupt priority levels, power off flag, ALE dis-
able, serial port automatic address recognition,
serial port framing error detection, 64-byte en-
cryption array, and 3 program lock bits. These
features cannot be used with the older versions
of 80C51BH/80C31BH. The newer version of
80C51BH/80C31BH will have change identifier
‘‘A’’ appended to the lot number.
Table 2. Status of the External Pins during Idle and Power Down
Mode
Program
Memory
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power Down
Internal
0
0
Data
Data
Data
Data
Power Down
External
0
0
Float
Data
Data
Data
6
相關PDF資料 |
PDF描述 |
|---|---|
| D882SS | NPN EPITAXIAL SILICON TRANSISTOR |
| D882 | TO-126 Plastic-Encapsulate Transistors |
| D8LC40 | Super Fast Recovery Rectifiers (400V 8A) |
| D950-CORE | 16-Bit Fixed Point Digital Signal Processor DSP Core |
| D965-R | NPN Plastic-Encapsulate Transistors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| D80C51BH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| D80C51BH-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| D80C51BH-2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| D80C51BH-24 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| D80C51BH-60XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。