參數資料
型號: D6571E
廠商: Electronic Theatre Controls, Inc.
英文描述: Chip for an All-Digital Telephone Answering Machine with Flash Memory Interface
中文描述: 芯片的全數字電話應答機與快閃記憶體介面
文件頁數: 14/117頁
文件大小: 551K
代理商: D6571E
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
D6571E Data Sheet
DS6571E.2
DSP GROUP, INC., 3120 SCOTT BOULEVARD
SANTA CLARA, CA 95054 PH: 408 986-4300 FAX: 408 986-4490
14
sending the Idle mode status word. The D6571E
assigns the next available message number to a newly
recorded message. The first message will be assigned
the number “0”, the second message will be assigned
the number “1”, and so on, up to “127”.
Record mode can be terminated by sending a Record
command with non-zero “Tail Cut” factor (TCF). The
D6571E stops recording and automatically deletes the
last n*TCF seconds from memory. The value of the TCF
is 0.160 seconds for 8000 Hz sampling rate and 0.178
seconds for 7200 Hz sampling rate. The D6571E then
returns to Idle mode. For PCM recording the value of
the TCF is 0.240 seconds and 0.266 seconds for 8 KHz
and 7.2 KHz sampling rate respectively.
Host can pause recording by sending Record command
with REC MODE = 10. The D6571E will stay in Record
mode, monitor line but won’t store data into flash. The
Host can send Record command with REC MODE = 00
to continue recording or terminate recording by Idle or
Tail Cut command.
Host can suspend recording (Record command with
REC MODE = 01). The D6571E will terminate recording
and go to Idle mode. The Host can instruct the D6571E
to perform another operation (other than Record), for
example, CID, Tone Generation, etc. Note that message
playback, voice prompt playback, and new message
recording is not available during record suspend.
Then Host may instruct the D6571E to resume recording
of the message that has been suspended. Alternatively
the Host can close the suspended message and then
start new message recording.
The Host may instruct the D6571E to change
compression rate, enable/disable Gap Coding and
Loopback (REC MODE = 11 and TONE GEN = 1). New
mode will be set in the bits NEW BIT RATE (bits 8 - 6),
LB DIS (bit 5), and GAP (bit 4).
Host can also instruct the D6571E to report current
offset in the message being recorded (REC MODE = 11
and TON GEN = 0).
A message will not be stored in the Flash memory if the
actual message length is less than 1 second. After
performing the tail cut function, or if the message length
is less than 1 second, the Garbage Collection
Recommended bit will be set (1) in the status of the
Read Memory Status command.
If the Flash memory has become full, the Memory Full
bit (bit 7) in the status word is set. The D6571E stops
recording, remains in Record mode, and continues to
perform line monitoring.
During Record mode, the HOST can instruct the D6571E
to generate a tone from the predefined tone table. The
HOST should issue a Record command with the “T” bit
(bit 9) set to “1”, Tone Gain (bits 8-5) and “Tone Index”
(bits 4-0). Tone generation will end if “Tone Index” is
“00000” along with the “T” bit set to “1”. For more
details about tone generation, see Tone Generation
command.
In Record mode, the input signal is “Looped Back” and
transmitted through the output of the CODEC. This can
be used for call screening or other purposes. If the
“Loop Back” is not necessary, the HOST can disable
this function by setting the “LB DIS” bit (bit 5) in the
first record command to “1”. The “LB DIS” bit should
usually be set to “1” if the tone generation function
during Record is used.
In case of “cold start” the Record will not be activated,
the D6571E remains in Idle mode and returns Idle status.
Playback
In playback mode, the D6571E performs message
playback and line monitoring. In the first playback
command, the HOST instructs the D6571E which
message to play, and at what F
LEXI
S
PEECH
speed.
The message number is defined in bits 0-6 and can be
from 0 to 127. The F
LEXI
S
PEECH
speed is defined in
bits
7-9.
To play a message at normal speed, the FLEXI
speed should be “000”. Other playback speeds, from 0.5
to 2.0 (50% - 200%) of the normal speed can be selected
according to the following table:
FLEXI SPEED
SPEED
PLAYBACK
1.0
0.5
0.7
1.0
1.3
1.5
1.75
2.0
OF
Bit 9
0
0
0
0
1
1
1
1
Bit 8
0
0
1
1
0
0
1
1
Bit 7
0
1
0
1
0
1
0
1
The second playback command instructs the D6571E to
play back the message from the predefined offset
location. This offset information is defined in units of
相關PDF資料
PDF描述
D658S14SEITE1BIS5 SCR / Diode Presspacks
D659S14SEITE1BIS5 SCR / Diode Presspacks
D6694ZOV301RA300
D6694ZOV102RA720
D6694ZOV131RA140
相關代理商/技術參數
參數描述
D65792-000 制造商:TE Connectivity 功能描述:Fuse Chip 0.75A Fast 2-Pin Solder Pad Surface Mount T/R 制造商:TE Connectivity 功能描述:1206SFF075F/63-2 - Tape and Reel 制造商:TE Connectivity 功能描述:FUSE 0.75A 63V FAST SMD 1206 制造商:TE Connectivity / Raychem 功能描述:FUSE 0.75A 63V FAST SMD 1206 制造商:TE CONNECTIVITY RAYCHEM-POLYSWITCH 功能描述:El Fuse / 1206SFF075F/63-2
D657ZOV271RA140 制造商:Maida Development Company 功能描述:
D-658 制造商:Triad Magnetics 功能描述:
D6582ZOV681RX260/CL 制造商:Maida Development Company 功能描述:
D65840GJ029 制造商:NEC Electronics Corporation 功能描述:ELECTRONIC COMPONENT