- 您現在的位置：買賣IC網 > PDF目錄9589 > CYW305OXCT (Silicon Laboratories Inc)IC CLOCK W305 SOLANO 56SSOP PDF資料下載
參數資料
| 型號： | CYW305OXCT |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK W305 SOLANO 56SSOP |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/頻率發生器 |
| PLL： | 是 |
| 主要目的： | Intel CPU 服務器 |
| 輸入： | 晶體 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:15 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 200MHz |
| 電源電壓： | 2.375 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 56-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
W305B
...................... Document #: 38-07262 Rev. *B Page 14 of 20
Programmable Output Frequency, Watchdog
Timer and Recovery Output Frequency
Functional Description
The Programmable Output Frequency feature allows users to
generate any CPU output frequency from the range of 50 MHz
to 248 MHz. Cypress offers the most dynamic and the simplest
programming interface for system developers to utilize this
feature in their platforms.
The Watchdog Timer and Recovery Output Frequency
features allow users to implement a recovery mechanism
when the system hangs or getting unstable. System BIOS or
other control software can enable the Watchdog timer before
they attempt to make a frequency change. If the system hangs
and a Watchdog timer time-out occurs, a system reset will be
generated and a recovery frequency will be activated.
All the related registers are summarized in the following table.
Table 6. Register Summary
Name
Description
Pro_Freq_EN
Programmable output frequencies enabled
0 = disabled (default)
1 = enabled
When it is disabled, the operating output frequency will be determined by either the latched value of
FS[4:0] inputs or the programmed value of SEL[4:0]. If FS_Override bit is clear, latched FS[4:0] inputs
will be used. If FS_Override bit is set, programmed value of SEL[4:0] will be used.
When it is enabled, the CPU output frequency will be determined by the programmed value of
CPUFSEL_N, CPUFSEL_M and the PLL Gear Constant. The program value of FS_Override, SEL[4:0]
or the latched value of FS[4:0] will determine the PLL Gear Constant and the frequency ratio between
CPU and other frequency outputs
FS_Override
When Pro_Freq_EN is cleared or disabled,
0 = Select operating frequency by FS input pins (default)
1 = Select operating frequency by SEL bits in SMBus control bytes
When Pro_Freq_EN is set or enabled,
0 = Frequency output ratio between CPU and other frequency groups and the PLL Gear Constant are
based on the latched value of FS input pins (default)
1 = Frequency output ratio between CPU and other frequency groups and the PLL Gear Constant are
based on the programmed value of SEL bits in SMBus control bytes
CPU_FSEL_N,
CPU_FSEL_M
When Prog_Freq_EN is set or enabled, the values programmed in CPU_FSEL_N[7:0] and
CPU_FSEL_M[6:0] determines the CPU output frequency. The new frequency will start to load
whenever there is an update to either CPU_FSEL_N[7:0] or CPU_FSEL_M[6:0]. Therefore, it is recom-
mended to use Word or Block write to update both registers within the same SMBus bus operation.
The setting of FS_Override bit determines the frequency ratio for CPU, SDRAM, AGP and SDRAM.
When FS_Override is cleared or disabled, the frequency ratio follows the latched value of the FS input
pins. When FS_Override is set or enabled, the frequency ratio follows the programmed value of SEL
bits in SMBus control bytes.
ROCV_FREQ_SEL
ROCV_FREQ_SEL determines the source of the recover frequency when a Watchdog timer time-out
occurs. The clock generator will automatically switch to the recovery CPU frequency based on the
selection on ROCV_FREQ_SEL.
0 = From latched FS[4:0]
1 = From the settings of ROCV_FREQ_N[7:0] & ROCV_FREQ_M[6:0]
ROCV_FREQ_N[7:0],
ROCV_FREQ_M[6:0]
When ROCV_FREQ_SEL is set, the values programmed in ROCV_FREQ_N[7:0] and
ROCV_FREQ_M[6:0] will be used to determine the recovery CPU output frequency when a Watchdog
timer time-out occurs
The setting of FS_Override bit determines the frequency ratio for CPU, SDRAM, AGP and SDRAM.
When it is cleared, the same frequency ratio stated in the Latched FS[4:0] register will be used.
When it is set, the frequency ratio stated in the SEL[4:0] register will be used.
The new frequency will start to load whenever there is an update to either ROCV_FREQ_N[7:0] and
ROCV_FREQ_M[6:0]. Therefore, it is recommended to use Word or Block write to update both registers
within the same SMBus bus operation.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS9250BF-12 | IC FREQ TIMING GENERATOR 56-SSOP |
| PI90LV387AE | IC 16 DIFF LINE DVR HS 64-TSSOP |
| CY28323OXCT | IC CLOCK BROOKDALE GPENT4 48SSOP |
| VE-23K-MY-S | CONVERTER MOD DC/DC 40V 50W |
| ISL8563ECB | XMITTER/RCVR RS562/232 18-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYW311OXC | 功能描述:時鐘發生器及支持產品 Sys Clk VIATM Pro266 DDR Chipset W311 DS RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| CYW311OXCT | 功能描述:時鐘發生器及支持產品 Sys Clk VIATM Pro266 DDR Chipset W311 DS RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| CYW312OXC | 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:FTG for VIA⑩ K7 Series Chipset with Programmable Output Frequency |
| CYW312OXCT | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FTG for VIA⑩ K7 Series Chipset with Programmable Output Frequency |
| CYW320OXC-3 | 功能描述:時鐘合成器/抖動清除器 Legacy, W320-03 datasheet RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。