
CYS25G0101DX
Document #: 38-02009 Rev. *J
Page 7 of 15
Maximum Ratings
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Storage Temperature .................................
–
65
°
C to +150
°
C
Ambient Temperature with
Power Applied.............................................
–
55
°
C to +125
°
C
V
CC
Supply Voltage to Ground Potential .......
–
0.5V to +4.2V
V
DDQ
Supply Voltage to Ground Potential .....
–
0.5V to +4.2V
DC Voltage Applied to HSTL Outputs
in High-Z State .....................................
–
0.5V to V
DDQ
+ 0.5V
DC Voltage Applied to Other Outputs
in High-Z State .......................................
–
0.5V to V
CC
+ 0.5V
Output Current into LVTTL Outputs (LOW)..................30 mA
DC Input Voltage....................................
–
0.5V to V
CC
+ 0.5V
Static Discharge Voltage...........................................> 1100V
(per MIL-STD-883, Method 3015)
Latch-up Current.....................................................> 200 mA
Table 1. DC Specifications
—
LVTTL
Power-up Requirements
Power supply sequencing is not required if you are configuring
VDDQ=3.3volts and all power supplies pins are connected to
the same 3.3 volt power supply.
Power supply sequencing is required if you are configuring
VDDQ=1.5volts. Power must be applied in the following
sequence: VCC (3.3) followed by VDDQ (1.5). Power supply
ramping may occur simultaneously as long as the VCC/VDDQ
relationship is maintained.
Operating Range
Range
Commercial
Industrial
Ambient
Temperature
0
°
C to +70
°
C
–
40
°
C to +85
°
C 1.4V to 1.6V
[4]
V
DDQ
V
CC
1.4V to 1.6V
[4]
3.3V ± 10%
3.3V ± 10%
Parameter
LVTTL Outputs
V
OHT
V
OLT
I
OS
LVTTL Inputs
V
IHT
V
ILT
I
IHT
I
ILT
Capacitance
C
IN
Description
Test Conditions
Min.
Max.
Unit
Output HIGH Voltage
Output LOW Voltage
Output Short Circuit Current
V
CC
= Min., I
OH
=
–
10.0 mA
V
CC
= Min., I
OL
= 10.0 mA
V
OUT
= 0V
2.4
V
V
0.4
–
90
–
20
mA
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
Low = 2.1V, High = V
CC
+ 0.5V
Low =
–
3.0V, High = 0.8
V
CC
= Max., V
IN
= V
CC
V
CC
= Max., V
IN
= 0V
2.1
–
0.3
V
CC
–
0.3
0.8
50
–
50
V
V
μ
A
μ
A
Input Capacitance
V
CC
= Max., @
f
= 1 MHz
5
pF
Table 2. DC Specifications
—
Power
Parameter
Power
I
CC1
I
SB
Description
Test Conditions
Typ.
Max.
Unit
Active Power Supply Current
Standby Current
300
347
5
mA
mA
Table 3. DC Specifications
—
Differential LVPECL Compatible Inputs (REFCLK)
[5]
Parameter
V
INSGLE
V
DIFFE
V
IEHH
V
IELL
I
IEH
I
IEL
Capacitance
C
INE
Note:
5.
See
Figure 2
for differential waveform definition.
Description
Test Conditions
Min.
200
400
Max.
600
1200
V
CC
–
0.3
V
CC
–
1.45
750
Unit
mV
mV
V
V
μ
A
μ
A
Input Single-ended Swing
Input Differential Voltage
Highest Input HIGH Voltage
Lowest Input LOW Voltage
Input HIGH Current
Input LOW Current
V
CC
–
1.2
V
CC
–
2.0
V
IN
= V
IEHH
Max.
V
IN
= V
IELL
Min.
–
200
Input Capacitance
4
pF