- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C68014A-56LFXC (CYPRESS SEMICONDUCTOR CORP) D-SSK 110 KER PDF資料下載
參數資料
| 型號： | CY7C68014A-56LFXC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | D-SSK 110 KER |
| 中文描述： | 8-BIT, EEPROM, 48 MHz, MICROCONTROLLER, QCC56 |
| 封裝： | 8 X 8 MM, LEAD FREE, MO-220, QFN-56 |
| 文件頁數： | 48/55頁 |
| 文件大?。?/td> | 1958K |
| 代理商： | CY7C68014A-56LFXC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
CY7C68013A/CY7C68014A
CY7C68015A/CY7C68016A
Document #: 38-08032 Rev. *G
Page 48 of 55
9.16.2
Single and Burst Synchronous Write
The
Figure 9-18
shows the timing relationship of the SLAVE
FIFO signals during a synchronous write using IFCLK as the
synchronizing clock. The diagram illustrates a single write
followed by burst write of 3 bytes and committing all 4 bytes as
a short packet using the PKTEND pin.
At t = 0 the FIFO address is stable and the signal SLCS is
asserted. (SLCS may be tied low in some applications)
Note:
t
SFA
has a minimum of 25 ns. This means when IFCLK
is running at 48 MHz, the FIFO address set-up time is more
than one IFCLK cycle.
At t = 1, the external master/peripheral must outputs the
data value onto the data bus with a minimum set up time of
t
SFD
before the rising edge of IFCLK.
At t = 2, SLWR is asserted. The SLWR must meet the set-
up time of t
SWR
(time from asserting the SLWR signal to the
rising edge of IFCLK) and maintain a minimum hold time of
t
WRH
(time from the IFCLK edge to the deassertion of the
SLWR signal). If SLCS signal is used, it must be asserted
with SLWR or before SLWR is asserted. (i.e. the SLCS and
SLWR signals must both be asserted to start a valid write
condition).
While the SLWR is asserted, data is written to the FIFO and
on the rising edge of the IFCLK, the FIFO pointer is incre-
mented. The FIFO flag will also be updated after a delay of
t
XFLG
from the rising edge of the clock.
The same sequence of events are also shown for a burst write
and are marked with the time indicators of T = 0 through 5.
Note: For the burst mode, SLWR and SLCS are left asserted
for the entire duration of writing all the required data values. In
this burst write mode, once the SLWR is asserted, the data on
the FIFO data bus is written to the FIFO on every rising edge
of IFCLK. The FIFO pointer is updated on each rising edge of
IFCLK. In
Figure 9-18
, once the four bytes are written to the
FIFO, SLWR is deasserted. The short 4-byte packet can be
committed to the host by asserting the PKTEND signal.
There is no specific timing requirement that needs to be met
for asserting PKTEND signal with regards to asserting the
SLWR signal. PKTEND can be asserted with the last data
value or thereafter. The only requirement is that the set-up time
t
SPE
and the hold time t
PEH
must be met. In the scenario of
Figure 9-18
, the number of data values committed includes the
last value written to the FIFO. In this example, both the data
value and the PKTEND signal are clocked on the same rising
edge of IFCLK. PKTEND can also be asserted in subsequent
clock cycles. The FIFOADDR lines should be held constant
during the PKTEND assertion.
Although there are no specific timing requirement for the
PKTEND assertion, there is a specific corner case condition
that needs attention while using the PKTEND to commit a one
byte/word packet. Additional timing requirements exists when
the FIFO is configured to operate in auto mode and it is desired
to send two packets: a full packet (full defined as the number
of bytes in the FIFO meeting the level set in AUTOINLEN
register) committed automatically followed by a short one
byte/word packet committed manually using the PKTEND pin.
In this case, the external master must make sure to assert the
PKTEND pin atleast one clock cycle after the rising edge that
caused the last byte/word to be clocked into the previous auto
committed packet (the packet with the number of bytes equal
to what is set in the AUTOINLEN register). Refer to
Figure 9-
10
for further details on this timing.
IFCLK
SLWR
FLAGS
DATA
Figure 9-18. Slave FIFO Synchronous Write Sequence and Timing Diagram
[19]
t
SWR
t
WRH
t
SFD
t
XFLG
t
IFCLK
N
>= t
SWR
>= t
WRH
N+3
PKTEND
N+2
t
XFLG
t
SFA
t
FAH
t
SPE
t
PEH
FIFOADR
SLCS
t
SFD
t
SFD
t
SFD
N+1
t
FDH
t
FDH
t
FDH
t
FDH
t=0
t=1
t=2
t=3
t
SFA
t
FAH
T=1
T=0
T=2
T=5
T=3
T=4
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C68014A-56PVXC | EZ-USB FX2LP USB Microcontroller |
| CY7C68015A-56LFXC | EZ-USB FX2LP USB Microcontroller |
| CY7C68013A-128AXC | CAC 2C 2#12 PIN PLUG |
| CY7C68024 | EZ-USB NX2LP USB 2.0 NAND Flash Controller(EZ-USB NX2LP USB 2.0 NAND閃存控制器) |
| CY7C68023 | EZ-USB NX2LP USB 2.0 NAND Flash Controller(EZ-USB NX2LP USB 2.0 NAND閃存控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C68014A-56LTXC | 功能描述:8位微控制器 -MCU USB HS Controller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C68014A-56PVXC | 功能描述:8位微控制器 -MCU EZ USB FX2LP Battery Apps LO COM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C68014A-BAXC | 制造商:Cypress Semiconductor 功能描述:MCU 8BIT CISC ROMLESS 3.3V 100TQFP - Trays |
| CY7C68015A-56LFXC | 功能描述:8位微控制器 -MCU EZ USB FX2LP LO PWR Extra GPIO COM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C68015A-56LTXC | 功能描述:USB 接口集成電路 USB HS Controller RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。