- 您現在的位置：買賣IC網 > PDF目錄379006 > CY28346ZCT (CYPRESS SEMICONDUCTOR CORP) Clock Synthesizer with Differential CPU Outputs PDF資料下載
參數資料
| 型號： | CY28346ZCT |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | XO, clock |
| 英文描述： | Clock Synthesizer with Differential CPU Outputs |
| 中文描述： | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封裝： | 6 X 12 MM, MO-153, TSSOP2-56 |
| 文件頁數： | 3/20頁 |
| 文件大小： | 179K |
| 代理商： | CY28346ZCT |
CY28346
Document #: 38-07331 Rev. *B
Page 3 of 20
Two-Wire SMBus Control Interface
The two-wire control interface implements a Read/Write slave
only interface according to SMBus specification.
The device will accept data written to the D2 address and data
may read back from address D3. It will not respond to any other
addresses, and previously set control registers are retained as
long as power in maintained on the device.
Serial Control Registers
Following the acknowledge of the Address Byte, two additional
bytes must be sent:
1.
“
Command code
“
byte
2.
“
Byte count
”
byte.
Although the data (bits) in the command is considered
“
don
’
t
care,
”
it must be sent and will be acknowledged. After the
Command Code and the Byte Count have been acknowl-
edged, the sequence (Byte 0, Byte 1, and Byte 2) described
below will be valid and acknowledged.
Byte 0: CPU Clock Register
[2,3]
Bit
7
@Pup
0
Pin#
Description
Spread Spectrum Enable. 0 = Spread Off, 1 = Spread On
This is a Read and Write control bit.
CPU Clock Power-down Mode Select. 0 = Drive CPUT(0:2) to 4 or 6 IREF and drive CPUC(0:2)
LOW when PD# is asserted LOW. 1 = Tri-state all CPU outputs. This is only applicable when
PD# is LOW. It is not applicable to CPU_STP#.
3V66_1/VCH Frequency Select, 0 = 66M selected, 1 = 48M selected
This is a Read and Write control bit.
CPU_STP#. Reflects the current value of the external CPU_STP# (pin 53) This bit is
Read-only.
Reflects the current value of the internal PCI_STP# function when read. Internally PCI_STP#
is a logical AND function of the internal SMBus register bit and the external PCI_STP# pin.
Frequency Select Bit 2. Reflects the value of SEL2 (pin 40). This bit is Read-only.
Frequency Select Bit 1. Reflects the value of SEL1 (pin 55). This bit is Read-only.
Frequency Select Bit 0. Reflects the value of SEL0 (pin 54). This bit is Read-only.
6
0
5
0
35
4
Pin 53
44,45,48,49,5
1,52
10,11,12,13,1
6,17,18
3
Pin 34
2
1
0
Pin 40
Pin 55
Pin 54
Byte 1: CPU Clock Register
Bit
7
6
@Pup
Pin 43
0
Pin#
43
53
Description
MULT0 (Pin 43) Value. This bit is Read-only.
CPUT/C(0:2) Output Functionality Control When CPU_STP# is Asserted. 0 = Drive
CPUT(0:2) to 4 or 6 IREF and drive CPUC(0:2) LOW when CPU_STP# asserted LOW.
1 = three-state all CPU outputs. This bit will override Byte0,Bit6 such that even if it is 0,
when PD# goes LOW the CPU outputs will be three-stated.
CPU2 Functionality Control When CPU_STP# is Asserted LOW. 1 = Free Running, 0 =
Stopped LOW with CPU_STP# asserted LOW. This is a Read and Write control bit.
CPU1 Functionality Control When CPU_STP# is Asserted LOW. 1 = Free Running, 0 =
Stopped LOW with CPU_STP# asserted LOW. This is a Read and Write control bit.
CPUT0 Functionality Control When CPU_STP# is Asserted LOW. 1 = Free Running, 0 =
Stopped LOW with CPU_STP# asserted LOW. This is a Read and Write control bit.
CPUT/C2 Output Control. 1 = enabled, 0 = disable HIGH and CPUC2 disables LOW. This
is a Read and Write control bit.
CPUT/C1 Output Control. 1 = enabled, 0 = disable HIGH and CPUC1 disables LOW. This
is a Read and Write control bit.
CPUT/C0 Output Control. 1 = enabled, 0 = disable HIGH and CPUC0 disables LOW. This
is a Read and Write control bit.
5
0
44,45
4
0
48,49
3
0
51,52
2
1
44,45
1
1
48,49
0
1
51,52
Notes:
2.
3.
PU = internal pull-up. PD = internal pull-down. T = tri-level logic input with valid logic voltages of LOW = < 0.8V, T = 1.0
–
1.8V and HIGH = > 2.0V.
The
“
Pin#
”
column lists the relevant pin number where applicable. The
“
@Pup
”
column gives the default state at power-up.
相關PDF資料 |
PDF描述 |
|---|---|
| CY28347 | HDC-HA-48-SVL1/29 RoHS Compliant: Yes |
| CY28347ZC | Universal Single-chip Clock Solution for VIA P4M266/KM266 DDR Systems |
| CY28347ZCT | Universal Single-chip Clock Solution for VIA P4M266/KM266 DDR Systems |
| CY28347OC | Universal Single-chip Clock Solution for VIA P4M266/KM266 DDR Systems |
| CY28347OCT | Universal Single-chip Clock Solution for VIA P4M266/KM266 DDR Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY28346ZI-2 | 功能描述:時鐘合成器/抖動清除器 NB clk for Intel 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28346ZI-2T | 功能描述:時鐘合成器/抖動清除器 NB clk for Intel 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28346ZXC | 功能描述:時鐘合成器/抖動清除器 NB Clk Intel Brkdale 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28346ZXC-2 | 功能描述:時鐘合成器/抖動清除器 NB Clk Intel Brkdale 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28346ZXC-2T | 功能描述:時鐘合成器/抖動清除器 NB Clk Intel Brkdale 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。