- 您現在的位置：買賣IC網 > PDF目錄295215 > CAT28F102NA-12T 64K X 16 FLASH 12V PROM, 120 ns, PQCC44 PDF資料下載
參數資料
| 型號： | CAT28F102NA-12T |
| 元件分類： | PROM |
| 英文描述： | 64K X 16 FLASH 12V PROM, 120 ns, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 14/15頁 |
| 文件大?。?/td> | 107K |
| 代理商： | CAT28F102NA-12T |
CAT28F102
8
Doc. No. 1014, Rev. A
READ OPERATIONS
Read Mode
A Read operation is performed with both CE and OE low
and with WE high. VPP can be either high or low,
however, if VPP is high, the Set READ command has to
be sent before reading data (see Write Operations). The
data retrieved from the I/O pins reflects the contents of
the memory location corresponding to the state of the 16
address pins. The respective timing waveforms for the
read operation are shown in Figure 5. Refer to the AC
Read characteristics for specific timing parameters.
Signature Mode
The signature mode allows the user to identify the IC
manufacturer and the type of device while the device
resides in the target system. This mode can be activated
in either of two ways; through the conventional method
of applying a high voltage (12V) to address pin A9 or by
sending an instruction to the command register (see
Write Operations).
The conventional mode is entered as a regular READ
mode by driving the CE and OE pins low (with WE high),
and applying the required high voltage on address pin A9
while all other address lines are held at VIL.
A Read cycle from address 0000H retrieves the binary
code for the IC manufacturer on outputs I/O0 to I/O15:
CATALYST Code = 0000 0000 0011 0001 (0031H)
A Read cycle from address 0001H retrieves the binary
code for the device on outputs I/O0 to I/O15.
28F102 Code = 0000 0000 0101 0001 (0051H)
Standby Mode
With CE at a logic-high level, the CAT28F102 is placed
in a standby mode where most of the device circuitry is
disabled, thereby substantially reducing power
consumption. The outputs are placed in a high-impedance
state.
Figure 5. A.C. Timing for Read Operation
tEHQZ(tDF)
ADDRESSES
CE (E)
OE (G)
WE (W)
DATA (I/O)
HIGH-Z
POWER UP
STANDBY
DEVICE AND
ADDRESS SELECTION
OUPUTS
ENABLED
DATA VALID
STANDBY
ADDRESS STABLE
OUTPUT VALID
tAVQV (tACC)
tELQX (tLZ)
tGLQX (tOLZ)
tGLQV (tOE)
tELQV (tCE)
tAXQX(tOH)
tGHQZ (tDF)
tAVAV (tRC)
POWER DOWN
HIGH-Z
tWHGL
Main Menu
相關PDF資料 |
PDF描述 |
|---|---|
| CAT28LV64H-25TE13 | 8K X 8 EEPROM 3V, 250 ns, PDSO32 |
| CAT28LV64JI-35TE13 | 8K X 8 EEPROM 3V, 350 ns, PDSO28 |
| CAT28LV64T-30TE13 | 8K X 8 EEPROM 3V, 300 ns, PDSO32 |
| CAT28LV64JA-25T | 8K X 8 EEPROM 3V, 250 ns, PDSO28 |
| CAT3200TDI-TE13 | 0.2 A SWITCHED CAPACITOR REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT28F512G12 | 功能描述:閃存 64 X 8 512K 120ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F512G-12 | 制造商:ON Semiconductor 功能描述:Flash Memory IC |
| CAT28F512G-12T | 功能描述:閃存 512K-Bit CMOS 閃存 Memory RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F512G90 | 功能描述:閃存 64 X 8 512K 90ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F512G-90 | 制造商:ON Semiconductor 功能描述:IC FLASH 512KBIT 90NS LCC-32 |
發布緊急采購，3分鐘左右您將得到回復。