- 您現在的位置：買賣IC網 > PDF目錄295215 > CAT28F010T-90 (ON SEMICONDUCTOR) 128K X 8 FLASH 12V PROM, 90 ns, PDSO32 PDF資料下載
參數資料
| 型號： | CAT28F010T-90 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | PROM |
| 英文描述： | 128K X 8 FLASH 12V PROM, 90 ns, PDSO32 |
| 封裝： | 8 X 20 MM, TSOP-32 |
| 文件頁數： | 14/15頁 |
| 文件大?。?/td> | 137K |
| 代理商： | CAT28F010T-90 |
CAT28F010
8
Doc. No. MD-1019, Rev. F
2008 SCILLC. All rights reserved.
Characteristics subject to change without notice
READ OPERATIONS
Read Mode
A Read operation is performed with both CE and OE low
and with WE high. VPP can be either high or low,
however, if VPP is high, the Set READ command has to
be sent before reading data (see Write Operations). The
data retrieved from the I/O pins reflects the contents of
the memory location corresponding to the state of the 17
address pins. The respective timing waveforms for the
read operation are shown in Figure 3. Refer to the AC
Read characteristics for specific timing parameters.
Signature Mode
The signature mode allows the user to identify the IC
manufacturer and the type of device while the device
resides in the target system. This mode can be activated
in either of two ways; through the conventional method
of applying a high voltage (12V) to address pin A9 or by
sending an instruction to the command register (see
Write Operations).
The conventional mode is entered as a regular READ
mode by driving the CE and OE pins low (with WE high),
and applying the required high voltage on address pin A9
while all other address lines are held at VIL.
A Read cycle from address 0000H retrieves the binary
code for the IC manufacturer on outputs I/O0 to I/O7:
CATALYST Code = 00110001 (31H)
A Read cycle from address 0001H retrieves the binary
code for the device on outputs I/O0 to I/O7.
28F010 Code = 1011 0100 (B4H)
Standby Mode
With CE at a logic-high level, the CAT28F010 is placed
in a standby mode where most of the device circuitry is
disabled, thereby substantially reducing power con-
sumption. The outputs are placed in a high-impedance
state.
Figure 3. A.C. Timing for Read Operation
28F010 F05
tEHQZt(DF)
ADDRESSES
CE (E)
OE (G)
WE (W)
DATA (I/O)
HIGH-Z
POWER UP
STANDBY
DEVICE AND
ADDRESS SELECTION
OUPUTS
ENABLED
DATA VALID
STANDBY
ADDRESS STABLE
OUTPUT VALID
tAVQV (tACC)
tELQX (tLZ)
tGLQX (tOLZ)
tGLQV (tOE)
tELQV (tCE)
tAXQXt(OH)
tGHQZ (tDF)
tAVAV (tRC)
POWER DOWN
HIGH-Z
tWHGL
相關PDF資料 |
PDF描述 |
|---|---|
| CAT28F102NA-12T | 64K X 16 FLASH 12V PROM, 120 ns, PQCC44 |
| CAT28LV64H-25TE13 | 8K X 8 EEPROM 3V, 250 ns, PDSO32 |
| CAT28LV64JI-35TE13 | 8K X 8 EEPROM 3V, 350 ns, PDSO28 |
| CAT28LV64T-30TE13 | 8K X 8 EEPROM 3V, 300 ns, PDSO32 |
| CAT28LV64JA-25T | 8K X 8 EEPROM 3V, 250 ns, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT28F010TI-12 | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F010TI90 | 制造商:ON Semiconductor 功能描述:Flash Parallel 5V 1Mbit 128K x 8bit 90ns 32-Pin TSOP |
| CAT28F010TI-90 | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F010TR-12 | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F010TR-90 | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。