參數資料
型號: C8051F005-TB
廠商: Silicon Laboratories Inc
文件頁數: 43/171頁
文件大小: 0K
描述: BOARD PROTOTYPING W/C8051F005
標準包裝: 1
類型: MCU
適用于相關產品: C8051F005
所含物品:
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 18.9. SCON: Serial Port Control Register
R/W
Reset Value
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
00000000
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
SFR Address:
(bit addressable)
0x98
Bits7-6: SM0-SM1: Serial Port Operation Mode.
These bits select the Serial Port Operation Mode.
SM0
SM1
Mode
0
Mode 0: Synchronous Mode
0
1
Mode 1: 8-Bit UART, Variable Baud Rate
1
0
Mode 2: 9-Bit UART, Fixed Baud Rate
1
Mode 3: 9-Bit UART, Variable Baud Rate
Bit5:
SM2: Multiprocessor Communication Enable.
The function of this bit is dependent on the Serial Port Operation Mode.
Mode 0: No effect
Mode 1: Checks for valid stop bit.
0: Logic level of stop bit is ignored.
1: RI will only be activated if stop bit is logic level 1.
Mode 2 and 3: Multiprocessor Communications Enable.
0: Logic level of ninth bit is ignored.
1: RI is set and an interrupt is generated only when the ninth bit is logic 1.
Bit4:
REN: Receive Enable.
This bit enables/disables the UART receiver.
0: UART reception disabled.
1: UART reception enabled.
Bit3:
TB8: Ninth Transmission Bit.
The logic level of this bit will be assigned to the ninth transmission bit in Modes 2 and 3. It
is not used in Modes 0 and 1. Set or cleared by software as required.
Bit2:
RB8: Ninth Receive Bit.
The bit is assigned the logic level of the ninth bit received in Modes 2 and 3. In Mode 1, if
SM2 is logic 0, RB8 is assigned the logic level of the received stop bit. RB8 is not used in
Mode 0.
Bit1:
TI: Transmit Interrupt Flag.
Set by hardware when a byte of data has been transmitted by the UART (after the 8
th bit in
Mode 0, or at the beginning of the stop bit in other modes). When the UART interrupt is
enabled, setting this bit causes the CPU to vector to the UART interrupt service routine.
This bit must be cleared manually by software
Bit0:
RI: Receive Interrupt Flag.
Set by hardware when a byte of data has been received by the UART (after the 8
th bit in
Mode 0, or after the stop bit in other modes – see SM2 bit for exception). When the
UART interrupt is enabled, setting this bit causes the CPU to vector to the UART interrupt
service routine. This bit must be cleared manually by software.
137
Rev. 1.7
相關PDF資料
PDF描述
SK101M250ST CAP ALUM 100UF 250V 20% RADIAL
SLPX472M063E3P3 CAP ALUM 4700UF 63V 20% SNAP
SDR-R SCOTCH CODE REFILL R
C8051F206-TB BOARD PROTOTYPING W/C8051F206
0210490992 CABLE JUMPER 1.25MM .102M 29POS
相關代理商/技術參數
參數描述
C8051F005-TB-K 功能描述:BOARD PROTOTYPING W/C8051F005 制造商:silicon labs 系列:- 零件狀態:在售 板類型:評估平臺 類型:MCU 8-位 核心處理器:8051 操作系統:- 平臺:- 配套使用產品/相關產品:C8051F0xx 安裝類型:固定 內容:板 標準包裝:1
C8051F006 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F006-GQ 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F006-GQR 功能描述:8位微控制器 -MCU 32KB 12ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F006R 功能描述:8位微控制器 -MCU C +-12Bit 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT