參數資料
型號： ATTINY26L-8PU
廠商： Atmel
文件頁數： 83/169頁
文件大?。?/td> 0K
描述： IC MCU AVR 2K 5V 8MHZ 20-DIP
產品培訓模塊： MCU Product Line Introduction
tinyAVR Introduction
標準包裝： 18
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 16
程序存儲器容量： 2KB（1K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 128 x 8
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 11x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-DIP（0.300"，7.62mm）
包裝： 管件
產品目錄頁面： 612 (CN2011-ZH PDF)
配用： ATSTK600-RC08-ND - STK600 ROUTING CARD AVR
ATSTK600-ND - DEV KIT FOR AVR/AVR32
ATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
ATSTK505-ND - ADAPTER KIT FOR 14PIN AVR MCU
其它名稱： ATTINY26L-8PJ
ATTINY26L-8PJ-ND
20
1477K–AVR–08/10
ATtiny26(L)
The EEPROM Read Enable Signal – EERE – is the read strobe to the EEPROM. When the cor-
rect address is set up in the EEAR Register, the EERE bit must be set. When the EERE bit is
cleared (zero) by hardware, requested data is found in the EEDR Register. The EEPROM read
access takes one instruction and there is no need to poll the EERE bit. When EERE has been
set, the CPU is halted for four cycles before the next instruction is executed.
The user should poll the EEWE bit before starting the read operation. If a write operation is in
progress when new data or address is written to the EEPROM I/O Registers, the write operation
will be interrupted, and the result is undefined.
Note:
1. Uses 1 MHz clock, independent of CKSEL-Fuse settings.
EEPROM Write During
Power-down Sleep
Mode
When entering Power-down sleep mode while an EEPROM write operation is active, the
EEPROM write operation will continue, and will complete before the write access time has
passed. However, when the write operation is completed, the crystal Oscillator continues run-
ning, and as a consequence, the device does not enter Power-down entirely. It is therefore
recommended to verify that the EEPROM write operation is completed before entering Power-
down.
Preventing EEPROM
Corruption
During periods of low VCC, the EEPROM data can be corrupted because the supply voltage is
too low for the CPU and the EEPROM to operate properly. These issues are the same as for
board level systems using the EEPROM, and the same design solutions should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too low. First,
a regular write sequence to the EEPROM requires a minimum voltage to operate correctly. Sec-
ondly, the CPU itself can execute instructions incorrectly, if the supply voltage for executing
instructions is too low.
EEPROM data corruption can easily be avoided by following these design recommendations
(one is sufficient):
1. Keep the AVR RESET active (low) during periods of insufficient power supply voltage.
This can be done by enabling the internal Brown-out Detector (BOD) if the operating volt-
age matches the detection level. If not, an external Brown-out Reset Protection circuit
can be applied.
2. Keep the AVR core in Power-down Sleep mode during periods of low VCC. This will pre-
vent the CPU from attempting to decode and execute instructions, effectively protecting
the EEPROM Registers from unintentional writes.
Store constants in Flash memory if the ability to change memory contents from software is not
required. Flash memory can not be updated by the CPU, and will not be subject to corruption.
I/O Memory
The I/O space definition of the ATtiny26(L) is shown in Table 2
Table 1. EEPROM Programming Time
Symbol
Number of Calibrated RC
Oscillator Cycles(1)
Typical Programming
Time
EEPROM Write (from CPU)
8448
8.5 ms
Table 2. ATtiny26(L) I/O Space(1)
Address Hex
Name
Function
$3F ($5F)
SREG
Status Register
$3D ($5D)
SP
Stack Pointer
$3B ($5B)
GIMSK
General Interrupt Mask Register
相關PDF資料
PDF描述
ATTINY28V-1AUR IC MCU AVR 2K 1.2MHZ 1.8V 32TQFP
ATTINY4313-MMH IC MCU AVR 4K FLASH 20QFN
ATTINY43U-SUR MCU AVR 4KB FLASH 8MHZ 20SOIC
ATTINY44A-MFR MCU AVR 4KB FLASH 20MHZ 20QFN
ATTINY48-AUR MCU AVR 4KB FLASH 12MHZ 32TQFP
相關代理商/技術參數
參數描述
ATTINY26L-8SC 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SI 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SI SL383 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 2KB Flash 3.3V/5V 20-Pin SOIC W T/R
ATtiny26L-8SU 功能描述:8位微控制器 -MCU 2kB Flash 128B EE 128B SRAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SUR 功能描述:8位微控制器 -MCU 2K FL 128B EE 128B SRAM ADC 8MHZ IND 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*