參數資料
型號： ATTINY26L-8PU
廠商： Atmel
文件頁數： 102/169頁
文件大小： 0K
描述： IC MCU AVR 2K 5V 8MHZ 20-DIP
產品培訓模塊： MCU Product Line Introduction
tinyAVR Introduction
標準包裝： 18
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 16
程序存儲器容量： 2KB（1K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 128 x 8
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 11x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-DIP（0.300"，7.62mm）
包裝： 管件
產品目錄頁面： 612 (CN2011-ZH PDF)
配用： ATSTK600-RC08-ND - STK600 ROUTING CARD AVR
ATSTK600-ND - DEV KIT FOR AVR/AVR32
ATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
ATSTK505-ND - ADAPTER KIT FOR 14PIN AVR MCU
其它名稱： ATTINY26L-8PJ
ATTINY26L-8PJ-ND
38
1477K–AVR–08/10
ATtiny26(L)
The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corre-
sponding interrupt mask is set (one). The activity on the external INT0 pin that activates the
interrupt is defined in the following table.
Note:
1. When changing the ISC10/ISC00 bits, INT0 must be disabled by clearing its Interrupt Enable
bit in the GIMSK Register. Otherwise an interrupt can occur when the bits are changed.
Idle Mode
When the SM1..0 bits are written to “00”, the SLEEP instruction makes the MCU enter Idle
mode, stopping the CPU but allowing Analog Comparator, ADC, USI, Timer/Counters, Watch-
dog, and the interrupt system to continue operating. This sleep mode basically halts clkCPU and
clkFLASH, while allowing the other clocks to run.
Idle mode enables the MCU to wake up from external triggered interrupts as well as internal
ones like the Timer Overflow and USI Start and Overflow interrupts. If wake-up from the Analog
Comparator interrupt is not required, the Analog Comparator can be powered down by setting
the ACD bit in the Analog Comparator Control and Status Register – ACSR. This will reduce
power consumption in Idle mode. If the ADC is enabled, a conversion starts automatically when
this mode is entered.
ADC Noise
Reduction Mode
When the SM1..0 bits are written to “01”, the SLEEP instruction makes the MCU enter ADC
Noise Reduction mode, stopping the CPU but allowing the ADC, the External Interrupts, the USI
start condition detection, and the Watchdog to continue operating (if enabled). This sleep mode
basically halts clkI/O, clkCPU, and clkFLASH, while allowing the other clocks to run.
This improves the noise environment for the ADC, enabling higher resolution measurements. If
the ADC is enabled, a conversion starts automatically when this mode is entered. Apart form the
ADC Conversion Complete interrupt, only an External Reset, a Watchdog Reset, a Brown-out
Reset, USI start condition interrupt, an EEPROM ready interrupt, an External Level Interrupt on
INT0, or a pin change interrupt can wake up the MCU from ADC Noise Reduction mode.
Power-down Mode When the SM1..0 bits are written to “10”, the SLEEP instruction makes the MCU enter Power-
down mode. In this mode, the External Oscillator is stopped, while the External Interrupts, the
USI start condition detection, and the Watchdog continue operating (if enabled). Only an Exter-
nal Reset, a Watchdog Reset, a Brown-out Reset, USI start condition interrupt, an External
Level Interrupt on INT0, or a pin change interrupt can wake up the MCU. This sleep mode basi-
cally halts all generated clocks, allowing operation of asynchronous modules only.
When waking up from Power-down mode, there is a delay from the wake-up condition occurs
until the wake-up becomes effective. This allows the clock to restart and become stable after
having been stopped. The wake-up period is defined by the same CKSEL Fuses that define the
reset time-out period, as described in “Clock Sources” on page 25.
Note that if a level triggered external interrupt or pin change interrupt is used from Power-down
mode, the changed level must be held for some time to wake up the MCU. This makes the MCU
less sensitive to noise.
Table 18. Interrupt 0 Sense Control(1)
ISC01
ISC00
Description
0
The low level of INT0 generates an interrupt request.
0
1
Any change on INT0 generates an interrupt request.
1
0
The falling edge of INT0 generates an interrupt request.
1
The rising edge of INT0 generates an interrupt request.
相關PDF資料
PDF描述
ATTINY28V-1AUR IC MCU AVR 2K 1.2MHZ 1.8V 32TQFP
ATTINY4313-MMH IC MCU AVR 4K FLASH 20QFN
ATTINY43U-SUR MCU AVR 4KB FLASH 8MHZ 20SOIC
ATTINY44A-MFR MCU AVR 4KB FLASH 20MHZ 20QFN
ATTINY48-AUR MCU AVR 4KB FLASH 12MHZ 32TQFP
相關代理商/技術參數
參數描述
ATTINY26L-8SC 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SI 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SI SL383 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 2KB Flash 3.3V/5V 20-Pin SOIC W T/R
ATtiny26L-8SU 功能描述:8位微控制器 -MCU 2kB Flash 128B EE 128B SRAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SUR 功能描述:8位微控制器 -MCU 2K FL 128B EE 128B SRAM ADC 8MHZ IND 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*