參數資料
型號： ATTINY26L-8PU
廠商： Atmel
文件頁數： 150/169頁
文件大?。?/td> 0K
描述： IC MCU AVR 2K 5V 8MHZ 20-DIP
產品培訓模塊： MCU Product Line Introduction
tinyAVR Introduction
標準包裝： 18
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 16
程序存儲器容量： 2KB（1K x 16）
程序存儲器類型： 閃存
EEPROM 大小： 128 x 8
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 11x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-DIP（0.300"，7.62mm）
包裝： 管件
產品目錄頁面： 612 (CN2011-ZH PDF)
配用： ATSTK600-RC08-ND - STK600 ROUTING CARD AVR
ATSTK600-ND - DEV KIT FOR AVR/AVR32
ATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
ATSTK505-ND - ADAPTER KIT FOR 14PIN AVR MCU
其它名稱： ATTINY26L-8PJ
ATTINY26L-8PJ-ND
81
1477K–AVR–08/10
ATtiny26(L)
Register
Descriptions
USI Data Register –
USIDR
The USI uses no buffering of the serial register, i.e., when accessing the Data Register (USIDR)
the serial register is accessed directly. If a serial clock occurs at the same cycle the register is
written, the register will contain the value written and no shift is performed. A (left) shift operation
is performed depending of the USICS1..0 bits setting. The shift operation can be controlled by
an external clock edge, by a Timer/Counter0 overflow, or directly by software using the USICLK
strobe bit. Note that even when no wire mode is selected (USIWM1..0 = 0) both the external
data input (DI/SDA) and the external clock input (SCK/SCL) can still be used by the Shift
Register.
The output pin in use, DO or SDA depending on the wire mode, is connected via the output latch
to the most significant bit (bit 7) of the Data Register. The output latch is open (transparent) dur-
ing the first half of a serial clock cycle when an external clock source is selected (USICS1 = 1),
and constantly open when an internal clock source is used (USICS1 = 0). The output will be
changed immediately when a new MSB written as long as the latch is open. The latch ensures
that data input is sampled and data output is changed on opposite clock edges.
Note that the corresponding Data Direction Register (DDRB2/1) to the pin must be set to one for
enabling data output from the Shift Register.
USI Status Register –
USISR
The Status Register contains interrupt flags, line status flags and the counter value.
Note that doing a Read-Modify-Write operation on USISR Register, i.e., using the SBI or CBI
instructions, will clear pending interrupt flags. It is recommended that register contents is altered
by using the OUT instruction only.
Bit 7 – USISIF: Start Condition Interrupt Flag
When Two-wire mode is selected, the USISIF flag is set (to one) when a start condition is
detected. When output disable mode or Three-wire mode is selected and (USICSx = 0b11 &
USICLK = 0) or (USICS = 0b10 & USICLK = 0), any edge on the SCK pin sets the flag.
An interrupt will be generated when the flag is set while the USISIE bit in USICR and the Global
Interrupt Enable Flag are set. The flag will only be cleared by writing a logical one to the USISIF
bit. Clearing this bit will release the start detection hold of SCL in Two-wire mode.
A start condition interrupt will wakeup the processor from all four sleep modes.
Bit 6 – USIOIF: Counter Overflow Interrupt Flag
This flag is set (one) when the 4-bit counter overflows (i.e., at the transition from 15 to 0). An
interrupt will be generated when the flag is set while the USIOIE bit in USICR and the Global
Interrupt Enable Flag are set. The flag will only be cleared if a one is written to the USIOIF bit.
Clearing this bit will release the counter overflow hold of SCL in Two-wire mode.
A counter overflow interrupt will wakeup the processor from Idle sleep mode.
Bit
7
6
5
4
3
2
1
0
$0F ($2F)
MSB
LSB
USIDR
Read/Write
R/W
Initial Value
0
Bit
7
6
5
4
3
210
$0E ($2E)
USISIF
USIOIF
USIPF
USIDC
USICNT3
USICNT2
USICNT1
USICNT0
USISR
Read/Write
R/W
R
R/W
Initial Value
0
相關PDF資料
PDF描述
ATTINY28V-1AUR IC MCU AVR 2K 1.2MHZ 1.8V 32TQFP
ATTINY4313-MMH IC MCU AVR 4K FLASH 20QFN
ATTINY43U-SUR MCU AVR 4KB FLASH 8MHZ 20SOIC
ATTINY44A-MFR MCU AVR 4KB FLASH 20MHZ 20QFN
ATTINY48-AUR MCU AVR 4KB FLASH 12MHZ 32TQFP
相關代理商/技術參數
參數描述
ATTINY26L-8SC 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SI 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SI SL383 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 2KB Flash 3.3V/5V 20-Pin SOIC W T/R
ATtiny26L-8SU 功能描述:8位微控制器 -MCU 2kB Flash 128B EE 128B SRAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY26L-8SUR 功能描述:8位微控制器 -MCU 2K FL 128B EE 128B SRAM ADC 8MHZ IND 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*