參數資料
型號： ATAM893T-TKQ
廠商： Atmel
文件頁數： 89/98頁
文件大小： 0K
描述： IC MON TIRE-PRESS ATARX9X SER
標準包裝： 4,000
系列： MARC4
核心處理器： MARC4
芯體尺寸： 4-位
速度： 4MHz
連通性： SSI（2 線，3 線）
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 16
程序存儲器容量： 4KB（4K x 8）
程序存儲器類型： EEPROM
EEPROM 大?。?/td> 64 x 16
RAM 容量： 256 x 4
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 6.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 20-SOIC（0.209"，5.30mm 寬）
包裝： 帶卷 (TR)
9
4680C–4BMCU–01/05
ATAM893-D
4.2.5
I/O Bus
The I/O ports and the registers of the peripheral modules are I/O mapped. All communication
between the core and the on-chip peripherals takes place via the I/O bus and the associated I/O
control. With the MARC4 IN and OUT instructions the I/O bus allows a direct read or write
access to one of the 16 primary I/O addresses. More about the I/O access to the on-chip periph-
erals is described in the section “Peripheral Modules”. The I/O bus is internal and is not
accessible by the customer on the final microcontroller device, but it is used as the interface for
the MARC4 emulation (see section “Emulation”).
4.2.6
Instruction Set
The MARC4 instruction set is optimized for the high level programming language qFORTH.
Many MARC4 instructions are qFORTH words. This enables the compiler to generate a fast and
compact program code. The CPU has an instruction pipeline allowing the controller to prefetch
an instruction from program memory at the same time as the present instruction is being exe-
cuted. The MARC4 is a zero address machine, the instructions containing only the operation to
be performed and no source or destination address fields. The operations are implicitly per-
formed on the data placed on the stack. There are one and two byte instructions which are
executed within 1 to 4 machine cycles. A MARC4 machine cycle is made up of two system clock
cycles (SYSCL). Most of the instructions are only one byte long and are executed in a single
machine cycle. For more information refer to the “MARC4 Programmer's Guide”.
4.2.7
Interrupt Structure
The MARC4 can handle interrupts with eight different priority levels. They can be generated
from the internal and external interrupt sources or by a software interrupt from the CPU itself.
Each interrupt level has a hard-wired priority and an associated vector for the service routine in
the program memory (see Table 4-2 on page 11). The programmer can postpone the processing
of interrupts by resetting the interrupt enable flag (I) in the CCR. An interrupt occurrence will still
be registered, but the interrupt routine only started after the I flag is set. All interrupts can be
masked, and the priority individually software configured by programming the appropriate control
register of the interrupting module (see section “Peripheral Modules”).
4.2.7.1
Interrupt Processing
For processing the eight interrupt levels, the MARC4 includes an interrupt controller with two
8-bit wide “interrupt pending” and “interrupt active” registers. The interrupt controller samples all
interrupt requests during every non-I/O instruction cycle and latches these in the interrupt pend-
ing register. If no higher priority interrupt is present in the interrupt active register, it signals the
CPU to interrupt the current program execution. If the interrupt enable bit is set, the processor
enters an interrupt acknowledge cycle. During this cycle a short call (SCALL) instruction to the
service routine is executed and the current PC is saved on the return stack.
An interrupt service routine is completed with the RTI instruction. This instruction resets the cor-
responding bits in the interrupt pending/active register and fetches the return address from the
return stack to the program counter. When the interrupt enable flag is reset (triggering of inter-
rupt routines are disabled), the execution of new interrupt service routines is inhibited but not the
logging of the interrupt requests in the interrupt pending register. The execution of the interrupt
is delayed until the interrupt enable flag is set again. Note that interrupts are only lost if an inter-
rupt request occurs while the corresponding bit in the pending register is still set (i.e., the
interrupt service routine is not yet finished).
相關PDF資料
PDF描述
TSC80251G2D-L16CER IC MCU 8BIT 16MHZ LO VOLT 44VQFP
TSC87251G2D-L16CER IC MCU 8BIT 32K OTP 16MHZ 44VQFP
PIC18F86K90-I/PTRSL MCU PIC 64K FLASH XLP 80TQFP
201692-4 CONN HOUSING PLUG 104POS BLACK
202800-2 CONN HOUSING RECEPT 160POS BLACK
相關代理商/技術參數
參數描述
ATAM893T-TKQYD 功能描述:4位微控制器 - MCU Marc4 micrium 4 k FLASH RoHS:否 最大時鐘頻率:32 KHz/4 MHz 程序存儲器大小:4 KB 封裝 / 箱體:SSO-20 制造商:Atmel 核心:MARC4 數據總線寬度:4 bit 安裝風格:SMD/SMT
ATAM893T-TKS 功能描述:IC MON TIRE-PRESS ATARX9X SER RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MARC4 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR)
ATAM893T-TKSYD 功能描述:4位微控制器 - MCU Marc4 micrium 4k FLASH RoHS:否 最大時鐘頻率:32 KHz/4 MHz 程序存儲器大小:4 KB 封裝 / 箱體:SSO-20 制造商:Atmel 核心:MARC4 數據總線寬度:4 bit 安裝風格:SMD/SMT
ATAM893X-TKHYZ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Flash Version for ATAR080, ATAR090/890 and ATAR092/892
ATAM893X-TKQYZ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Flash Version for ATAR080, ATAR090/890 and ATAR092/892
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*