參數資料
型號： AT91SAM7S32B-MU
廠商： Atmel
文件頁數： 16/165頁
文件大小： 0K
描述： IC MCU ARM7 32KB FLASH 48-VQFN
產品培訓模塊： MCU Product Line Introduction
標準包裝： 250
系列： SAM7S
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 55MHz
連通性： I²C，SPI，SSC，UART/USART
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 21
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 48-VFQFN 裸露焊盤
包裝： 托盤
配用： AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9
AT91SAM7S-EK-ND - KIT EVAL FOR ARM AT91SAM7S
112
SAM7S Series [DATASHEET]
6175M–ATARM–26-Oct-12
When programming is complete, the bit FRDY bit in the Flash Programming Status Register (MC_FSR) rises. If an
interrupt has been enabled by setting the bit FRDY in MC_FMR, the interrupt line of the Memory Controller is
activated.
Two errors can be detected in the MC_FSR register after a programming sequence:
Programming Error: A bad keyword and/or an invalid command have been written in the MC_FCR register.
Lock Error: At least one lock region to be erased is protected. The erase command has been refused and no
page has been erased. A Clear Lock Bit command must be executed previously to unlock the corresponding
lock regions.
19.2.4.3
Lock Bit Protection
Lock bits are associated with several pages in the embedded Flash memory plane. This defines lock regions in the
embedded Flash memory plane. They prevent writing/erasing protected pages.
After production, the device may have some embedded Flash lock regions locked. These locked regions are
reserved for a default application. Refer to the product definition section for the default embedded Flash mapping.
Locked sectors can be unlocked to be erased and then programmed with another application or other data.
The lock sequence is:
The Flash Command register must be written with the following value:
(0x5A << 24) | (lockPageNumber << 8 & PAGEN) | SLB
lockPageNumber is a page of the corresponding lock region.
When locking completes, the bit FRDY in the Flash Programming Status Register (MC_FSR) rises. If an
interrupt has been enabled by setting the bit FRDY in MC_FMR, the interrupt line of the Memory Controller is
activated.
A programming error, where a bad keyword and/or an invalid command have been written in the MC_FCR register,
may be detected in the MC_FSR register after a programming sequence.
It is possible to clear lock bits that were set previously. Then the locked region can be erased or programmed. The
unlock sequence is:
The Flash Command register must be written with the following value:
(0x5A << 24) | (lockPageNumber << 8 & PAGEN) | CLB
lockPageNumber is a page of the corresponding lock region.
When the unlock completes, the bit FRDY in the Flash Programming Status Register (MC_FSR) rises. If an
interrupt has been enabled by setting the bit FRDY in MC_FMR, the interrupt line of the Memory Controller is
activated.
A programming error, where a bad keyword and/or an invalid command have been written in the MC_FCR register,
may be detected in the MC_FSR register after a programming sequence.
The Unlock command programs the lock bit to 1; the corresponding bit LOCKSx in MC_FSR reads 0. The Lock
command programs the lock bit to 0; the corresponding bit LOCKSx in MC_FSR reads 1.
Note:
Access to the Flash in Read Mode is permitted when a Lock or Unlock command is performed.
19.2.4.4
General-purpose NVM Bits
General-purpose NVM bits do not interfere with the embedded Flash memory plane. (Does not apply to EFC1 on
the SAM7S512.) These general-purpose bits are dedicated to protect other parts of the product. They can be set
(activated) or cleared individually. Refer to the product definition section for the general-purpose NVM bit action.
The activation sequence is:
Start the Set General Purpose Bit command (SGPB) by writing the Flash Command Register with the SEL
command and the number of the general-purpose bit to be set in the PAGEN field.
相關PDF資料
PDF描述
AT91SAM7SE256-AU IC ARM7 MCU FLASH 256K 128-LQFP
AT91SAM7SE32-AU MCU ARM 32K HS FLASH 128-LQFP
AT91SAM7X256B-CU IC MCU 256KB FLASH 100TFBGA
AT91SAM7XC256B-AU MCU ARM 256K HS FLASH 100-LQFP
AT91SAM9260B-CU-100 IC MCU ARM9 217LFBGA
相關代理商/技術參數
參數描述
AT91SAM7S32B-MU-999 功能描述:ARM微控制器 - MCU Green, Ind Temp MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S32-MU 功能描述:ARM微控制器 - MCU QFN IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S32-MU-999 功能描述:ARM微控制器 - MCU Microcontroller RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S512 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7S512-AU 功能描述:ARM微控制器 - MCU LQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*