- 您現在的位置：買賣IC網 > PDF目錄381356 > ASCELL3911 (AUSTRIAMICROSYSTEMS AG) ER 6C 6#16 SKT RECP LINE PDF資料下載
參數資料
| 型號： | ASCELL3911 |
| 廠商： | AUSTRIAMICROSYSTEMS AG |
| 元件分類： | 通信及網絡 |
| 英文描述： | ER 6C 6#16 SKT RECP LINE |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO14 |
| 封裝： | TSSOP-14 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 104K |
| 代理商： | ASCELL3911 |
ISM 868 MHz, 433 MHz and 315 MHz FSK Transmitter – Preliminary Data Sheet
ASCell3911
Rev. A, February 2000
Page 8 of 13
Austria Mikro Systeme International AG
5
GP
6
GP
Table 2:
Control bit description.
Single message transmission:
After completing the data transmission to the ASCell3911, the
μC may indicate ”end of transmission” by setting P4 (not end of transmit) to ”L” and pulls the
WAKEUP line to ”L”. Sensing this, 4 clock cycles later the ASCell3911 will switch the μC back to
standby mode, disabling the μC_CLK output, setting the active WAKEUP pin to ”L”. The AS-
Cell3911 will finish the transmission sequence and than turning off the XTAL oscillator to and
goes back to the standby mode too. The SMT/CMT bit is ”L” indicates the single transmission
mode.
Note: SMT/CMT is one bit of the control information.
Continuous message transmission:
After completing the data transmission to the AS-
Cell3911, the μC may indicate ”end of transmission” by setting P4 to ”L” and pulls the WAKEUP
line to ”L”. Sensing this, 4 clock cycles later the ASCell3911 will switch back to standby mode,
disabling the μC_CLK output, setting the active WAKEUP pin to ”L” and than turning off the XTAL
oscillator. The SMT/CMT bit is ”H” indicates the continuous transmission mode.
Note: SMT/CMT is one bit of the control information.
Due to the sophisticated tri-state - active/inactive pull-up configuration of the WAKEUP pin the
ASCell3911 does not drain current during its standby periods.
The interface implemented in the ASCell3911 system cell is a general, non-specialized example
only. It can be modified on customers demand.
2
Electrical Characteristics
2.1
Symbol
Absolute Maximum Ratings (non operating)
Parameter
Min
Max
Units
Note
VDD; VDDSYN
Positive supply voltage
-0,5
6
V
GND; GNDSYN
Negative supply voltage
0
0
V
Vin
Voltage at every input pin
Gnd-0,5
VCC+0,5
V
Iin
Input current into any pin except
supply pins
-10
10
mA
Latch-up Test
ESD
Electrostatic discharge
1k
V
1) 3)
ESD
IN
Electrostatic discharge of RF pins
500
V
1) 4)
Tstg
Storage temperature
-55
125
°C
Tlead
Lead temperature
260
°C
2)
1) Test according to MIL STD 883C, Method 3015.7. HBM: R=1,5 k
, C=100 pF, 5 positive pulses per pin against supply pin(s), 5
negative pulses per pin against supply pin(s).
2) 260 °C for 10 s (Reflow and Wave Soldering), 360 °C for 3 s (Manual soldering).
3) All pins except RF+, RF-, XTAL.
4) Pins RF+, RF-, XTAL.
相關PDF資料 |
PDF描述 |
|---|---|
| ASCELL3912 | ER 10C 10#16 SKT RECP LINE |
| ASD07H-12D12 | Isolated and Regulated 7 WATT Open Frame DC/DC Converter |
| ASD07H-12D15 | Isolated and Regulated 7 WATT Open Frame DC/DC Converter |
| ASD07H-12D5 | Isolated and Regulated 7 WATT Open Frame DC/DC Converter |
| ASD07H-12S12 | Isolated and Regulated 7 WATT Open Frame DC/DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ASCELL3912 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:ISM 868 MHz, 433 MHz and 315 MHz FSK Transmitter |
| ASCF21U | 制造商:ABRACON 制造商全稱:Abracon Corporation 功能描述:CERAMIC SURFACE-MOUNT 21.4MHz and 45MHz FUNDAMENTAL MONOLITHIC CRYSTAL FILTERS |
| ASCF21U15 | 制造商:ABRACON 制造商全稱:Abracon Corporation 功能描述:CERAMIC SURFACE-MOUNT 21.4MHz and 45MHz FUNDAMENTAL MONOLITHIC CRYSTAL FILTERS |
| ASCF21U20 | 制造商:ABRACON 制造商全稱:Abracon Corporation 功能描述:CERAMIC SURFACE-MOUNT 21.4MHz and 45MHz FUNDAMENTAL MONOLITHIC CRYSTAL FILTERS |
| ASCF21U30 | 制造商:ABRACON 制造商全稱:Abracon Corporation 功能描述:CERAMIC SURFACE-MOUNT 21.4MHz and 45MHz FUNDAMENTAL MONOLITHIC CRYSTAL FILTERS |
發布緊急采購，3分鐘左右您將得到回復。