參數資料
型號： AS7C33256PFS36A-133TQCN
廠商： ALLIANCE SEMICONDUCTOR CORP
元件分類： DRAM
英文描述： 3.3V 256K x 32/36 pipelined burst synchronous SRAM
中文描述： 256K X 36 STANDARD SRAM, 10 ns, PQFP100
封裝： 14 X 20 MM, LEAD FREE, TQFP-100
文件頁數： 5/20頁
文件大?。?/td> 527K
代理商： AS7C33256PFS36A-133TQCN
AS7C33256PFS32A
AS7C33256PFS36A
11/30/04, v.3.1
Alliance Semiconductor
P. 5 of 20
Signal descriptions
Snooze Mode
SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to I
SB2
. The duration of
SNOOZE MODE is dictated by the length of time the ZZ is in a High state.
The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE.
When the ZZ pin becomes a logic High, I
SB2
is guaranteed after the time t
ZZI
is met. After entering SNOOZE MODE, all inputs except ZZ
is disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successfully complete.
Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. Similarly, when exiting
SNOOZE MODE during t
PUS
, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of SNOOZE MODE.
Signal
CLK
I/O
I
Properties
CLOCK
Description
Clock. All inputs except OE, ZZ, LBO are synchronous to this clock.
A, A0, A1
I
SYNC
Address. Sampled when all chip enables are active and ADSC or ADSP are asserted.
DQ[a,b,c,d]
I/O
SYNC
Data. Driven as output when the chip is enabled and OE is active.
Master chip enable. Sampled on clock edges when ADSP or ADSC is active. When CE0
is inactive, ADSP is blocked. Refer to the Synchronous Truth Table for more
information.
CE0
I
SYNC
CE1, CE2
I
SYNC
Synchronous chip enables. Active HIGH and active LOW, respectively. Sampled on
clock edges when ADSC is active or when CE0 and ADSP are active.
ADSP
I
SYNC
Address strobe processor. Asserted LOW to load a new bus address or to enter standby
mode.
Address strobe controller. Asserted LOW to load a new address or to enter standby
mode.
ADSC
I
SYNC
ADV
I
SYNC
Advance. Asserted LOW to continue burst read/write.
GWE
I
SYNC
Global write enable. Asserted LOW to write all 32/36 bits. When HIGH, BWE and
BW[a:d] control write enable.
Byte write enable. Asserted LOW with GWE = HIGH to enable effect of BW[a:d]
inputs.
BWE
I
SYNC
BW[a,b,c,d] I
SYNC
Write enables. Used to control write of individual bytes when GWE = HIGH and BWE =
LOW. If any of BW[a:d] is active with GWE = HIGH and BWE = LOW the cycle is a
write cycle. If all BW[a:d] are inactive the cycle is a read cycle.
OE
I
ASYNC
Asynchronous output enable. I/O pins are driven when OE is active and the chip is in
read mode.
Selects Burst mode. When tied to V
DD
or left floating, device follows Interleaved Burst
order. When driven Low, device follows linear Burst order.
This signal is internally
pulled High.
LBO
I
STATIC
ZZ
I
ASYNC
Snooze. Places device in LOW power mode; data is retained. Connect to GND if unused.
NC
-
-
No connect
相關PDF資料
PDF描述
AS7C33256PFS36A-133TQI 3.3V 256K x 32/36 pipelined burst synchronous SRAM
AS7C332MFT18A-10TQI 3.3V 2M x 18 Flow-through synchronous SRAM
AS7C332MFT18A-10TQIN 3.3V 2M x 18 Flow-through synchronous SRAM
AS7C332MFT18A-75TQC 3.3V 2M x 18 Flow-through synchronous SRAM
AS7C332MFT18A-75TQCN 3.3V 2M x 18 Flow-through synchronous SRAM
相關代理商/技術參數
參數描述
AS7C33256PFS36A-133TQI 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3.3V 256K x 32/36 pipelined burst synchronous SRAM
AS7C33256PFS36A-133TQIN 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3.3V 256K x 32/36 pipelined burst synchronous SRAM
AS7C33256PFS36A-166TQC 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3.3V 256K x 32/36 pipelined burst synchronous SRAM
AS7C33256PFS36A-166TQCN 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3.3V 256K x 32/36 pipelined burst synchronous SRAM
AS7C33256PFS36A-166TQI 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3.3V 256K x 32/36 pipelined burst synchronous SRAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*