- 您現在的位置：買賣IC網 > PDF目錄381309 > AS3931 (AUSTRIAMICROSYSTEMS AG) 3D Low Power Wakeup Receiver PDF資料下載
參數資料
| 型號： | AS3931 |
| 廠商： | AUSTRIAMICROSYSTEMS AG |
| 元件分類： | 微波射頻器件 |
| 英文描述： | 3D Low Power Wakeup Receiver |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO16 |
| 文件頁數： | 26/30頁 |
| 文件大?。?/td> | 822K |
| 代理商： | AS3931 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁
26 - 30
AS3931
Datasheet - Extended Operation
10.6 Direct DATA Mode
In Direct Data Mode, the received DATA of a selected channel can be mapped to the WAKE pin. The DATA signal is the digital output of the
detector and is normally fed to the correlator, where it is scanned for the WAKE pattern
(see Figure 13)
. To get the DATA signal at the WAKE pin,
follow the steps:
1. Enable Test Mode: set T0 = 1 in Test Mode Register
2. Select Test Mode: set T1 = 0 and T2 = 0 in Test Mode Register
3. Select Channel: set C0 and C1 in the Channel Select Register
The Direct DATA signals can also be mapped to the RSSI pin, which then becomes a digital output pin. To do this, make this step:
Select RSSI output mode digital:set C2 = 0 and C3 = 1 in the Channel Select Register
Note:
The RSSI pin is only active if the CS signal is active (CS = 1), otherwise RSSI is high Z.
10.7 Correlator Modes
Operation of the correlators can be modified regarding the error tolerances for the Zero-Half-Bits. In this case, the number of Zero-Half-Bits that
is allowed to be invalid can be set from0 to 2. Please take into account that an increased error tolerance also reduces the immunity against
parasitic wakeups (WAKE detection when no data has been sent, due to noise or interferences).
10.8 Threshold Adaptation Filter Time Constant
Bit M4 is used to switch between a large and a small
τ
of the detector threshold adaptation filter. A large
τ
is recommended, because it increases
the noise margin. A small
τ
can be used to improve the wake sensitivity when non-specified Wake-Patterns are used.
10.9 RSSI and WAKE Pin Modes
This table gives an overview of the different signals that can be mapped to the RSSI and WAKE pin and how to programit.
Table 29. RSSI/WAKE-Pin Modes
B
C
R
R
C
C
W
T
T
Mode
CS
C3
C2
C1
C0
T0
T2
T1
WAKE-Pin: WAKE
X
X
X
X
X
0
X
X
WAKE-Pin: DATA1
X
X
X
0
0
1
0
0
WAKE-Pin: DATA2
X
X
X
0
1
1
0
0
WAKE-Pin: DATA3
X
X
X
1
0
1
0
0
WAKE-Pin: WAKE1
X
X
X
0
0
1
0
1
WAKE-Pin: WAKE2
X
X
X
0
1
1
0
1
WAKE-Pin: WAKE3
X
X
X
1
0
1
0
1
RSSI-Pin: WAKE
1
1
0
1
1
X
X
X
RSSI-Pin: DATA1
1
1
0
0
0
X
0
0
RSSI-Pin: DATA2
1
1
0
0
1
X
0
0
RSSI-Pin: DATA3
1
1
0
1
0
X
0
0
RSSI-Pin: WAKE1
1
1
0
0
0
X
0
1
RSSI-Pin: WAKE2
1
1
0
0
1
X
0
1
RSSI-Pin: WAKE3
1
1
0
1
0
X
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| AS3932-BTST | Programmable 3D LF Receiver; Package Type: TSSOP-16; Temperature Range: -40 - +85 °C; Supply Voltage: 2,40-3,60 |
| AS3932-BQFT | Programmable 3D LF Receiver; Package Type: QFN(4x4)-16; Temperature Range: -40 - +85 °C; Supply Voltage: 2,40-3,60 |
| AS4C1M16E5 | 5V 1M×16 CMOS DRAM (EDO)(5V 1M×16 CMOS動態RAM（擴展數據總線）) |
| AS4C1M16F5 | 5V 1M×16 CMOS DRAM (Fast-page Mode)(5V 1M×16 CMOS動態RAM（快速頁面模式）) |
| AS4C256K16E0-50TC | 5V 256Kx16 CMOS DRAM (EDO) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS3931 DB | 制造商:AMS 功能描述:BOARD DEMO FOR AS3931 制造商:AMS 功能描述:Demoboard for AS3931 3D Low Power Wakeup Receiver |
| AS39310FLF | 制造商:TT Electronics / IRC 功能描述:AS39310FLF |
| AS39310HLF | 制造商:TT Electronics / IRC 功能描述:AS39310HLF |
| AS39310JLF | 制造商:TT Electronics / IRC 功能描述:AS39310JLF |
| AS39311FLF | 制造商:TT Electronics / IRC 功能描述:AS39311FLF |
發布緊急采購，3分鐘左右您將得到回復。