- 您現在的位置：買賣IC網 > PDF目錄381262 > APA2068KAI-TUL (Anpec Electronics Corporation) Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) PDF資料下載
參數資料
| 型號： | APA2068KAI-TUL |
| 廠商： | Anpec Electronics Corporation |
| 英文描述： | Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) |
| 中文描述： | 立體聲2.6W音頻功率放大器（帶DC_Volume控制） |
| 文件頁數： | 22/27頁 |
| 文件大小： | 495K |
| 代理商： | APA2068KAI-TUL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁
Copyright
ANPEC Electronics Corp.
Rev. A.2 - Jul., 2005
APA2068
www.anpec.com.tw
22
Application Descriptions ( Cont.)
load is increased resulting in a nearly flat internal power
dissipation over the normal operating range.
Note that the efficiency of the amplifier is quite low for
lower power levels and rises sharply as power to the
load is increased resulting in a nearly flat internal power
dissipation over the normal operating range. Note that
the internal dissipation at full output power is less than
in the half power range. Calculating the efficiency for a
specific system is the key to proper power supply
design. For a stereo 1W audio system with 8
loads
and a 5V supply, the maximum draw on the power
supply is almost 3W.
A final point to remember about linear amplifiers (either
SE or BTL) is how to manipulate the terms in the
efficiency equation to utmost advantage when possible.
Note that in equation, V
DD
is in the denominator. This
indicates that as V
DD
goes down, efficiency goes up.
In other words, use the efficiency analysis to choose
the correct supply voltage and speaker impedance for
the application.
**High peak voltages cause the THD to increase.
Table 1. Efficiency Vs Output Power in 5-V/8
BTL
Systems
Power Dissipation
Whether the power amplifier is operated in BTL or SE
modes, power dissipation is a major concern. In equa-
BTL Amplifier Efficiency (Cont.)
Po (W) Efficiency (%) I
DD
(A)
V
PP
(V) P
D
(W)
0.25
31.25
0.16
2.00
0.55
0.50
47.62
0.21
2.83
0.55
1.00
66.67
0.30
4.00
0.5
1.25
78.13
0.32
4.47
0.35
tion13 states the maximum power dissipation point
for a SE mode operating at a given supply voltage and
driving a specified load.
V
DD
2
π
R
L
In BTL mode operation, the output voltage swing is
doubled as in SE mode. Thus the maximum power
dissipation point for a BTL mode operating at the same
given conditions is 4 times as in SE mode.
4V
DD
2
π
R
L
Since the APA2068 is a dual channel power amplifier,
the maximum internal power dissipation is 2 times
that both of equations depending on the mode of
operation. Even with this substantial increase in power
dissipation, the APA2068 does not require extra
heatsink. The power dissipation from equation14,
assuming a 5V-power supply and an 8
load, must
not be greater than the power dissipation that results
from the equation15 :
T
J,MAX
- T
A
θ
JA
For SOP16-P package with thermal pad, the thermal
resistance (
θ
JA
) is equal to 45
ο
C/W.
Since the maximum junction temperature (T
J,MAX
) of
APA2068 is 150
ο
C and the ambient temperature (T
A
)
is defined by the power system design, the maximum
power dissipation which the IC package is able to
handle can be obtained from equation15.
Once the power dissipation is greater than the maxi-
mum limit (P
D,MAX
), either the supply voltage (V
DD
) must
be decreased, the load impedance (R
L
) must be in-
creased or the ambient temperature should be reduced.
Thermal Pad Considerations
The thermal pad must be connected to ground. The
package with thermal pad of the APA2068 requires
special attention on thermal design. If the thermal
SE mode : P
D,MAX
=
(13)
2
2
BTL mode : P
D,MAX
=
(14)
2
2
P
D,MAX
=
(15)
相關PDF資料 |
PDF描述 |
|---|---|
| APA2308KITU | Class AB Stereo Headphone Driver |
| APA2822 | Dual Low-Voltage Power Amplifier |
| APA3544JI-TR | Class AB Stereo Headphone Driver with Mute |
| APA3544JI-TU | Class AB Stereo Headphone Driver with Mute |
| APA3544YI-TR | Rotary Switch; Contact Current Max:1.5A; No. of Poles:3; No. of Switch Positions:5; Indexing:30 ; Switch Terminals:Through Hole RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APA2069 | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) |
| APA2069_11 | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) |
| APA2069JI-TU | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) |
| APA2069JI-TUG | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) |
| APA2069JI-TUL | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.6W Audio Power Amplifier (with DC_Volume Control) |
發布緊急采購，3分鐘左右您將得到回復。