- 您現在的位置：買賣IC網 > PDF目錄364677 > AN-30 TOPSwitch-GX Forward Design Methodology PDF資料下載
參數資料
| 型號： | AN-30 |
| 英文描述： | TOPSwitch-GX Forward Design Methodology |
| 中文描述： | 的TOPSwitch - GX系列正向設計方法 |
| 文件頁數： | 26/40頁 |
| 文件大?。?/td> | 311K |
| 代理商： | AN-30 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AN-30
26
B
12/02
Figure B2. Circuit to Adjust Main Regulated Output Voltage to Higher Value.
V
V
I
R
R
D
N
N
R
R
R
D
IN
BZL
L
D
C
IL
B
P
AB
D
C
IL
=
+
+
+
+
1
mode noise. Monitor the current in the DRAIN pin of
TOPSwitch-GX
with a current probe and an oscilloscope.
Connect an adjustable low voltage DC power supply to the
feedback circuit as shown in Figure B2.
2. Set the oscilloscope to read the duty ratio from the waveform
of the
TOPSwitch-GX
drain current. Most digital
oscilloscopes will provide a direct readout of the numerical
value.
3. Adjust the low voltage DC power supply to 15 V.
4. Operate the converter at full load. Adjust V
to the value
that corresponds to the duty ratio limit specified in the data
sheet for a device at the low end of the tolerance range. The
DC input voltage for these conditions is given by
(B1)
where D
is the minimum DC
at the I
of 190
μ
A, and
the other terms are as they are defined in the text and
Appendix A
.
5. Adjust the duty ratio to D
by forcing the main output to
regulate at a higher voltage. To do this, reduce the voltage
of the bench power supply from 15 V until the duty ratio
measured from the drain current is D
IL
.
6. Verify that the current into the L pin is within 5% of I
L
. The
voltmeter should read 19 mV when I
L
is 190
μ
A.
If it is not possible to adjust the circuit to meet these conditions,
the circuit is not guaranteed to operate properly with all devices
in the specified range of tolerance. Repeat the design with
revised parameters.
Added Network to Adjust
Regulated Output
TL431
RTN
OPTO
1N4148
3.3 k
3.3 k
0 VDC to +15 VDC
Adjustable Power Supply
V
MAIN
+
_
Start with the adjustable power supply at 15 V. By lowering the
output of the external supply a threshold will be reached where the
diode will become forward biased. Lowering the adjustable supply
further will force the main output to a higher regulation voltage.
Main Output Regulator
PI-2846-041502
相關PDF資料 |
PDF描述 |
|---|---|
| AN-31 | DPA-Switch Forward Converter Design Guide |
| AN-32 | TOPSwitch-GX Flyback Design Methodology |
| AN-37 | LinkSwitch-TN Design Guide |
| AN-995A | Electronic Ballasts Using the Cost-Saving IR215X Drivers(153.99 k) |
| AN0416NA | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 30MA I(D) | DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN300 | 功能描述:環境檢測設備 Large Vane CFM/CMM Thermo-Anemometer RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration |
| AN3000-521P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AN0625-521P |
| AN3001 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:PIN diode Vector Modulators - Fundamentals and Drive Requirements |
| AN-3001 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Application Note AN-3001 Optocoupler Input Drive Circuits |
| AN-3002 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Low Current Input Circuit Ideas |
發布緊急采購，3分鐘左右您將得到回復。