- 您現在的位置：買賣IC網 > PDF目錄366481 > AM29LV128MH93FI (Advanced Micro Devices, Inc.) 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control PDF資料下載
參數資料
| 型號： | AM29LV128MH93FI |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control |
| 中文描述： | 128兆位（8 M中的x 16-Bit/16 M中的x 8位）的MirrorBit⑩3.0伏特，只有統一部門閃存與VersatileI內存/ O控制 |
| 文件頁數： | 12/65頁 |
| 文件大?。?/td> | 1222K |
| 代理商： | AM29LV128MH93FI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
10
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to V
IL
. CE# is the power
control and selects the device. OE# is the output con-
trol and gates array data to the output pins. WE#
should remain at V
IH
.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No com-
mand is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid
data on the device data outputs. The device remains
enabled for read access until the command register
contents are altered.
See “Reading Array Data” for more information. Refer
to the AC Read-Only Operations table for timing speci-
fications and to Figure 14 for the timing diagram. Refer
to the DC Characteristics table for the active current
specification on reading array data.
Page Mode Read
The device is capable of fast page mode read and is
compatible with the page mode Mask ROM read oper-
ation. This mode provides faster read access speed
for random locations within a page. The page size of
the device is 4 words/8 bytes. The appropriate page is
selected by the higher address bits A(max)–A2. Ad-
dress bits A1–A0 in word mode (A1–A-1 in byte mode)
determine the specific word within a page. This is an
asynchronous operation; the microprocessor supplies
the specific word location.
The random or initial page access is equal to t
ACC
or
t
CE
and subsequent page read accesses (as long as
the locations specified by the microprocessor falls
within that page) is equivalent to t
PACC
. When CE# is
deasserted and reasserted for a subsequent access,
the access time is t
ACC
or t
CE
. Fast page mode ac-
cesses are obtained by keeping the “read-page ad-
dresses” constant and changing the “intra-read page”
addresses.
Writing Commands/Command Sequences
To write a command or command sequence (which in-
cludes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to V
IL
, and OE# to V
IH
.
The device features an
Unlock Bypass
mode to facili-
tate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are re-
quired to program a word or byte, instead of four. The
“Word/Byte Program Command Sequence” section
has details on programming data to the device using
both standard and Unlock Bypass command se-
quences.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. Table 2 indicates the address
space that each sector occupies.
Refer to the DC Characteristics table for the active
current specification for the write mode. The AC Char-
acteristics section contains timing specification tables
and timing diagrams for write operations.
Write Buffer
Write Buffer Programming allows the system write to a
maximum of 16 words/32 bytes in one programming
operation. This results in faster effective programming
time than the standard programming algorithms. See
“Write Buffer” for more information.
Accelerated Program Operation
The device offers accelerated program operations
through the ACC function. This is one of two functions
provided by the WP#/ACC pin. This function is prima-
rily intended to allow faster manufacturing throughput
at the factory.
If the system asserts V
HH
on this pin, the device auto-
matically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sector
groups, and uses the higher voltage on the pin to re-
duce the time required for program operations. The
system would use a two-cycle program command se-
quence as required by the Unlock Bypass mode. Re-
moving V
HH
from the WP#/ACC pin returns the device
to normal operation. Note that the WP#/ACC pin must
not be at V
HH
for operations other than accelerated
programming, or device damage may result. WP# has
an internal pullup; when unconnected, WP# is at V
IH
.
Autoselect Functions
If the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in
this mode. Refer to the Autoselect Mode and Autose-
lect Command Sequence sections for more informa-
tion.
Standby Mode
When the system is not reading or writing to the de-
vice, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at V
IO
± 0.3 V.
(Note that this is a more restricted voltage range than
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV128MH93PCI | 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control |
| AM29LV128ML103EI | 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control |
| AM29LV128ML103FI | 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control |
| AM29LV128ML103PCI | 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control |
| AM29LV128ML113EI | 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV128ML113REI | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 128M-Bit 16M x 8/8M x 16 110ns 56-Pin TSOP |
| AM29LV128ML123REI | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 128M-Bit 16M x 8/8M x 16 120ns 56-Pin TSOP |
| AM29LV128ML-123REI | 制造商:Advanced Micro Devices 功能描述:8M X 16 FLASH 3V PROM, 120 ns, PDSO56 |
| AM29LV160BT-120EI | 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 90ns 48-Pin TSOP Tray |
| AM29LV160BT80SC | 制造商:AMD 功能描述:* |
發布緊急采購，3分鐘左右您將得到回復。