- 您現在的位置：買賣IC網 > PDF目錄11200 > ADUC842BCPZ8-5 (Analog Devices Inc)IC MCU 8KB FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC842BCPZ8-5 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 43/88頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 8KB FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 16.78MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | DMA，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.75 V ~ 5.25 V |
| 數據轉換器： | A/D 8x12b，D/A 2x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
ADuC841/ADuC842/ADuC843
Rev. 0 | Page 48 of 88
I2C COMPATIBLE INTERFACE
The ADuC841/ADuC842/ADuC843 support a fully licensed
I2C serial interface. The I2C interface is implemented as a full
hardware slave and software master. SDATA is the data I/O pin,
and SCLOCK is the serial clock. These two pins are shared with
the MOSI and SCLOCK pins of the on-chip SPI interface. To
enable the I2C interface, the SPI interface must be turned off
(see SPE in Table 18) or the SPI interface must be moved to
P3.3, P3.4, and P3.5 via the CFG841.1/CFG842.1 bit. Application
Note uC001 describes the operation of this interface as imple-
mented and is available from the MicroConverter website at
Three SFRs are used to control the I2C interface and are
described in the following tables.
I2CCON
I2C Control Register
SFR Address
E8H
Power-On Default
00H
Bit Addressable
Yes
Table 19. I2CCON SFR Bit Designations, Master Mode
Bit No.
Name
Description
7
I2C Software Master Data Output Bit (Master Mode Only).
This data bit is used to implement a master I2C transmitter interface in software. Data written to this bit is output on
the SDATA pin if the data output enable (MDE) bit is set.
6
MDE
I2C Software Master Data Output Enable Bit (Master Mode Only).
Set by the user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable the SDATA pin as an input (Rx).
5
MCO
I2C Software Master Clock Output Bit (Master Mode Only).
This data bit is used to implement a master I2C transmitter interface in software. Data written to this bit is output on
the SCLOCK pin.
4
MDI
I2C Software Master Data Input Bit (Master Mode Only).
This data bit is used to implement a master I2C receiver interface in software. Data on the SDATA pin is latched into
this bit on SCLOCK if the data output enable (MDE) bit is 0.
3
I2CM
I2C Master/Slave Mode Bit.
Set by the user to enable I2C software master mode.
Cleared by the user to enable I2C hardware slave mode.
2
----
Reserved.
1
----
Reserved.
0
----
Reserved.
Table 20. I2CCON SFR Bit Designations, Slave Mode
Bit No.
Name
Description
7
I2CSI
I2C Stop Interrupt Enable Bit.
Set by the user to enable I2C stop interrupts. If set, a stop bit that follows a valid start condition generates an
interrupt.
Cleared by the user to disable I2C stop interrupts.
6
I2CGC
I2C General Call Status Bit.
Set by hardware after receiving a general call address.
Cleared by the user.
5
I2CID1
I2C Interrupt Decode Bits.
4
I2CID0
Set by hardware to indicate the source of an I2C interrupt.
00
Start and Matching Address.
01
Repeated Start and Matching Address.
10
User Data.
11
Stop after a Start and Matching Address.
3
I2CM
I2C Master/Slave Mode Bit.
Set by the user to enable I2C software master mode.
Cleared by the user to enable I2C hardware slave mode.
相關PDF資料 |
PDF描述 |
|---|---|
| AT32UC3A1128-AUT | IC MCU AVR32 128KB FLASH 100TQFP |
| ATSAM3U4EA-CU | IC MCU 32BIT 256KB FLSH 144LFBGA |
| ADUC831BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
| ATSAM3X8CA-AU | IC MCU 2X256KB CORTEX-M3 100-QFP |
| VE-B3M-IX-F4 | CONVERTER MOD DC/DC 10V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC842BS | 制造商:AD 制造商全稱:Analog Devices 功能描述:12- Bit ADCs and DACs with Embedded Hi-Speed 62KB FLASH MCU |
| ADUC842BS62-3 | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3V 52-Pin MQFP 制造商:Analog Devices 功能描述:IC MICROCONTROLLER |
| ADUC842BS62-5 | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 16.7MHZ 5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:IC MICROCONTROLLER |
| ADUC842BSZ62-3 | 功能描述:IC ADC/DAC 12BIT W/MCU 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587 |
| ADUC842BSZ62-3 | 制造商:Analog Devices 功能描述:IC MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。