參數資料
型號： ADUC816BSZ
廠商： Analog Devices Inc
文件頁數： 32/68頁
文件大?。?/td> 0K
描述： IC MCU 8K FLASH ADC/DAC 52MQFP
產品培訓模塊： Process Control
標準包裝： 1
系列： MicroConverter® ADuC8xx
核心處理器： 8052
芯體尺寸： 8-位
速度： 12.58MHz
連通性： I²C，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 34
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 640 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 7x16b; D/A 1x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 52-QFP
包裝： 托盤
產品目錄頁面： 738 (CN2011-ZH PDF)
REV. 0
ADuC816
–38–
Using the Flash/EE Program Memory
The 8 Kbyte Flash/EE Program Memory array is mapped
into the lower 8 Kbytes of the 64 Kbytes program space
addressable by the ADuC816, and is used to hold user code
in typical applications.
The program memory Flash/EE memory arrays can be pro-
grammed in one of two modes, namely:
Serial Downloading (In-Circuit Programming)
As part of its factory boot code, the ADuC816 facilitates
serial code download via the standard UART serial port.
Serial download mode is automatically entered on power-up if
the external pin,
PSEN, is pulled low through an external
resistor as shown in Figure 27. Once in this mode, the user can
download code to the program memory array while the device is
sited in its target application hardware. A PC serial download
executable is provided as part of the ADuC816 QuickStart devel-
opment system. The Serial Download protocol is detailed in a
MicroConverter Applications Note uC004 available from the ADI
MicroConverter Website at www.analog.com/microconverter.
PSEN
ADuC816
PULL
PSEN LOW DURING RESET
TO CONFIGURE THE ADuC816
FOR SERIAL DOWNLOAD MODE
1k
Figure 27. Flash/EE Memory Serial Download Mode
Programming
Parallel Programming
The parallel programming mode is fully compatible with conven-
tional third party Flash or EEPROM device programmers. A
block diagram of the external pin configuration required to support
parallel programming is shown in Figure 28. In this mode, Ports 0,
1, and 2 operate as the external data and address bus interface,
ALE operates as the Write Enable strobe, and Port 3 is used as a
general configuration port that configures the device for various
program and erase operations during parallel programming.
The high voltage (12 V) supply required for Flash/EE program-
ming is generated using on-chip charge pumps to supply the high
voltage program lines.
VDD
GND
P3
PSEN
RESET
P0
P1
P2
ALE
ADuC816
5V
PROGRAM MODE
(SEE TABLE XII)
GND
PROGRAM
DATA
(D0–D7)
PROGRAM
ADDRESS
(A0–A13)
(P2.0 = A0)
(P1.7 = A13)
WRITE ENABLE
STROBE
COMMAND
ENABLE
P3.0
NEGATIVE
EDGE
P3.6
ENTRY
SEQUENCE
VDD
Figure 28. Flash/EE Memory Parallel Programming
Table XII. Flash/EE Memory Parallel Programming Modes
Port 3 Pins
Programming
0.7
0.6
0.5
0.4
0.3
0.2
0.1
Mode
XXXX
000Erase Flash/EE
Program, Data, and
Security Modes
XXXX
001Read Device
Signature/ID
X
1010Program Code Byte
X
0010Program Data Byte
X
1011Read Code Byte
X
0011Read Data Byte
XXXX
100Program Security
Modes
XXXX
101Read/Verify Security
Modes
All Other Codes
Redundant
Flash/EE Program Memory Security
The ADuC816 facilitates three modes of Flash/EE program
memory security. These modes can be independently activated,
restricting access to the internal code space. These security
modes can be enabled as part of the user interface available on all
ADuC816 serial or parallel programming tools referenced on the
MicroConverter web page at www.analog.com/microconverter.
The security modes available on the ADuC816 are described
as follows:
Lock Mode
This mode locks code in memory, disabling parallel program-
ming of the program memory although reading the memory in
parallel mode is still allowed. This mode is deactivated by initi-
ating a “code-erase” command in serial download or parallel
programming modes.
Secure Mode
This mode locks code in memory, disabling parallel programming
(program and verify/read commands) as well as disabling the
execution of a “MOVC” instruction from external memory,
which is attempting to read the op codes from internal memory.
This mode is deactivated by initiating a “code-erase” command
in serial download or parallel programming modes.
REV. A
相關PDF資料
PDF描述
VE-B32-IY-F2 CONVERTER MOD DC/DC 15V 50W
VE-B32-IY-F1 CONVERTER MOD DC/DC 15V 50W
VE-B32-CU-B1 CONVERTER MOD DC/DC 15V 200W
VE-B31-IY-F4 CONVERTER MOD DC/DC 12V 50W
3E106-1230 KV CONN PLUG IEEE 1394 VERTICAL
相關代理商/技術參數
參數描述
ADUC816BSZ-REEL 功能描述:IC MCU FLASH 16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC824 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual-Channel 16-/24-Bit ADCs with Embedded FLASH MCU
ADUC824BCP 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 56LFCSP - Bulk
ADUC824BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R
ADUC824BCPZ 功能描述:IC MCU 8K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*