- 您現在的位置：買賣IC網 > PDF目錄19389 > ADSP-BF544BBCZ-4A (Analog Devices Inc)IC CCD SIGNAL PROCESSOR 400BGA PDF資料下載
參數資料
| 型號： | ADSP-BF544BBCZ-4A |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/100頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD SIGNAL PROCESSOR 400BGA |
| 標準包裝： | 1 |
| 系列： | Blackfin® |
| 類型： | 定點 |
| 接口： | CAN，SPI，SSP，TWI，UART |
| 時鐘速率： | 400MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 196kB |
| 電壓 - 輸入/輸出： | 2.50V，3.30V |
| 電壓 - 核心： | 1.25V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 400-LFBGA，CSPBGA |
| 供應商設備封裝： | 400-CSPBGA（17x17） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
ADSP-BF542/ADSP-BF544/ADSP-BF547/ADSP-BF548/ADSP-BF549
Rev. C
|
Page 13 of 100
|
February 2010
Companding in hardware. Each SPORT can perform
A-law or μ-law companding according to ITU recommen-
dation G.711. Companding can be selected on the transmit
and/or receive channel of the SPORT without additional
latencies.
DMA operations with single-cycle overhead. Each SPORT
can receive and transmit multiple buffers of memory data
automatically. The processor can link or chain sequences of
DMA transfers between a SPORT and memory.
Interrupts. Each transmit and receive port generates an
interrupt upon completing the transfer of a data word or
after transferring an entire data buffer or buffers through
DMA.
Multichannel capability. Each SPORT supports 128 chan-
nels out of a 1024-channel window and is compatible with
the H.100, H.110, MVIP-90, and HMVIP standards.
SERIAL PERIPHERAL INTERFACE (SPI) PORTS
The ADSP-BF54x Blackfin processors have up to three SPI-
compatible ports that allow the processor to communicate with
multiple SPI-compatible devices.
Each SPI port uses three pins for transferring data: two data pins
(master output slave input, SPIxMOSI, and master input-slave
output, SPIxMISO) and a clock pin (serial clock, SPIxSCK). An
SPI chip select input pin (SPIxSS) lets other SPI devices select
the processor, and three SPI chip select output pins per SPI port
SPIxSELy let the processor select other SPI devices. The SPI
select pins are reconfigured general-purpose I/O pins. Using
these pins, the SPI ports provide a full-duplex, synchronous
serial interface, which supports both master/slave modes and
multimaster environments.
The SPI port’s baud rate and clock phase/polarities are pro-
grammable, and it has an integrated DMA controller,
configurable to support transmit or receive data streams. The
SPI’s DMA controller can only service unidirectional accesses at
any given time.
The SPI port’s clock rate is calculated as
Where the 16-bit SPI_BAUD register contains a value of
2 to 65,535.
During transfers, the SPI port transmits and receives simulta-
neously by serially shifting data in and out on its two serial data
lines. The serial clock line synchronizes the shifting and sam-
pling of data on the two serial data lines.
UART PORTS (UARTS)
The ADSP-BF54x Blackfin processors provide up to four full-
duplex universal asynchronous receiver/transmitter (UART)
ports. Each UART port provides a simplified UART interface to
other peripherals or hosts, supporting full-duplex, DMA-sup-
ported, asynchronous transfers of serial data. A UART port
includes support for five to eight data bits, one or two stop bits,
and none, even, or odd parity. Each UART port supports two
modes of operation:
PIO (programmed I/O). The processor sends or receives
data by writing or reading I/O-mapped UART registers.
The data is double-buffered on both transmit and receive.
DMA (direct memory access). The DMA controller trans-
fers both transmit and receive data. This reduces the
number and frequency of interrupts required to transfer
data to and from memory. Each UART has two dedicated
DMA channels, one for transmit and one for receive. These
DMA channels have lower default priority than most DMA
channels because of their relatively low service rates. Flexi-
ble interrupt timing options are available on the transmit
side.
Each UART port’s baud rate, serial data format, error code gen-
eration and status, and interrupts are programmable:
Supporting bit rates ranging from (fSCLK/1,048,576) to
(fSCLK) bits per second.
Supporting data formats from seven to 12 bits per frame.
Both transmit and receive operations can be configured to
generate maskable interrupts to the processor.
The UART port’s clock rate is calculated as
Where the 16-bit UART divisor comes from the UARTx_DLH
register (most significant 8 bits) and UARTx_DLL register (least
significant eight bits), and the EDBO is a bit in the
UARTx_GCTL register.
In conjunction with the general-purpose timer functions, auto-
baud detection is supported.
UART1 and UART3 feature a pair of UARTxRTS (request to
send) and UARTxCTS (clear to send) signals for hardware flow
purposes. The transmitter hardware is automatically prevented
from sending further data when the UARTxCTS input is de-
asserted. The receiver can automatically de-assert its
UARTxRTS output when the enhanced receive FIFO exceeds a
certain high-water level. The capabilities of the UARTs are fur-
ther extended with support for the Infrared Data Association
(IrDA) Serial Infrared Physical Layer Link Specification (SIR)
protocol.
CONTROLLER AREA NETWORK (CAN)
The ADSP-BF54x Blackfin processors offer up to two CAN con-
trollers that are communication controllers that implement the
controller area network (CAN) 2.0B (active) protocol. This pro-
tocol is an asynchronous communications protocol used in both
industrial and automotive control systems. The CAN protocol is
well suited for control applications due to its capability to com-
municate reliably over a network since the protocol
incorporates CRC checking, message error tracking, and fault
node confinement.
SPI Clock Rate
f
SCLK
2
SPI_BAUD
×
------------------------------------
=
UART Clock Rate
f
SCLK
16
1EDBO
–
()
UART_Divisor
×
------------------------------------------------------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21488KSWZ-4A | IC CCD SIGNAL PROCESSOR 100LQFP |
| ADSP-21488KSWZ-3A1 | IC DSP SHARC 400MHZ 100LQFP |
| JWS10028/A | PWR SUP 28.0V 3.6A SNG OUTPUT |
| MAX6505UTP020+T | IC TEMP SWITCH DL TRIP SOT23-6 |
| ADSP-BF533SBBZ400 | IC DSP CTLR 16BIT 400MHZ 169-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-BF544BBCZ-5A | 功能描述:IC DSP 16BIT 533MHZ 400CSBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-BF544BBCZ-5X | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE CONVERGENT MULTIMEDIA BLACKFIN PROCESSOR - Trays |
| ADSP-BF544MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-BF547BBCZ-5A | 功能描述:IC DSP 16BIT 533MHZ 400CSBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-BF547BBCZ-5X | 制造商:Analog Devices 功能描述:- Trays |
發布緊急采購，3分鐘左右您將得到回復。