參數資料
型號: ADSP-2184LBSTZ-160
廠商: Analog Devices Inc
文件頁數: 38/48頁
文件大?。?/td> 0K
描述: IC DSP CONTROLLER 16BIT 100LQFP
標準包裝: 1
系列: ADSP-21xx
類型: 定點
接口: 主機接口,串行端口
時鐘速率: 40MHz
非易失內存: 外部
芯片上RAM: 20kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 3.30V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-LQFP(14x14)
包裝: 托盤
ADSP-2184L/ADSP-2185L/ADSP-2186L/ADSP-2187L
Rev. C
|
Page 43 of 48
|
January 2008
TEST CONDITIONS
Figure 44 shows voltage reference levels for all ac measurements
(except output disable/enable).
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured out-
put high or low voltage to a high impedance state. The output
disable time (tDIS) is the difference of tMEASURED and tDECAY, as
shown in Figure 45. The time is the interval from when a refer-
ence signal reaches a high or low voltage level to when the
output voltages have changed by 0.5 V from the measured out-
put high or low voltage.
The decay time, tDECAY, is dependent on the capacitive load, CL,
and the current load, iL, on the output pin. It can be approxi-
mated by the following equation:
from which
is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.
Output Enable Time
Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start
driving. The output enable time (tENA) is the interval from when
a reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in Figure 45. If multiple pins (such as the data bus) are enabled,
the measurement value is that of the first pin to start driving.
ENVIRONMENTAL CONDITIONS
Figure 44. Voltage Reference Levels for AC Measurements (Except Output
Enable/Disable)
1.5V
INPUT
OR
OUTPUT
1.5V
tDECAY
CL 0.5V
×
iL
------------------------
=
tDIS
tMEASURED tDECAY
=
Figure 45. Output Enable/Disable
Figure 46. Equivalent Loading for AC Measurements (Including All Fixtures)
Table 28. Thermal Resistance
Rating Description1
1 Where the ambient temperature rating (TAMB) is:
TAMB = TCASE – (PD × θCA)
TCASE = case temperature in °C
PD = power dissipation in W
Symbol
LQFP
(
°C/W)
BGA
(
°C/W)
Thermal Resistance (Case-
to-Ambient)
θ
CA
48
63.3
Thermal Resistance
(Junction-to-Ambient)
θ
JA
50
70.7
Thermal Resistance
(Junction-to-Case)
θ
JC
27.4
2.0V
1.0V
tENA
REFERENCE
SIGNAL
OUTPUT
tDECAY
VOH
(MEASURED)
OUTPUT STOPS
DRIVING
OUTPUT STARTS
DRIVING
tDIS
tMEASURED
VOL
(MEASURED)
VOH (MEASURED) – 0.5V
VOL (MEASURED) + 0.5V
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
VOH
(MEASURED)
VOL
(MEASURED)
TO
OUTPUT
PIN
50pF
1.5V
I
OH
IOL
相關PDF資料
PDF描述
GMM44DRTF CONN EDGECARD 88POS DIP .156 SLD
ECM12DSEN CONN EDGECARD 24POS .156 EYELET
ADSP-BF524KBCZ-3C2 IC DSP CTRLR 300MHZ 289CSPBGA
HMC35DRTS-S93 CONN EDGECARD 70POS DIP .100 SLD
TAJC474K050RNJ CAP TANT 0.47UF 50V 10% 2312
相關代理商/技術參數
參數描述
ADSP-2184LBSTZ-1602 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2184N 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2184NBCA-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:4K PM/4K DM RAM,16-BIT,80 MIPS, 1.8V - Bulk
ADSP-2184NBST-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 100-Pin LQFP
ADSP-2184NBSTZ-320 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤