參數資料
型號: ADSP-2184LBSTZ-160
廠商: Analog Devices Inc
文件頁數: 3/48頁
文件大小: 0K
描述: IC DSP CONTROLLER 16BIT 100LQFP
標準包裝: 1
系列: ADSP-21xx
類型: 定點
接口: 主機接口,串行端口
時鐘速率: 40MHz
非易失內存: 外部
芯片上RAM: 20kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 3.30V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-LQFP(14x14)
包裝: 托盤
ADSP-2184L/ADSP-2185L/ADSP-2186L/ADSP-2187L
Rev. C
|
Page 11 of 48
|
January 2008
See Figure 9 and Figure 10 for illustration of the programmable
flag and composite control register and the system
control register.
Byte Memory Select
The ADSP-218xL’s BMS disable feature combined with the
CMS pin allows use of multiple memories in the byte memory
space. For example, an EPROM could be attached to the BMS
select, and a flash memory could be connected to CMS. Because
at reset BMS is enabled, the EPROM would be used for booting.
After booting, software could disable BMS and set the CMS sig-
nal to respond to BMS, enabling the flash memory.
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide,
external memory space used to store programs and data. Byte
memory is accessed using the BDMA feature. The byte memory
space consists of 256 pages, each of which is 16K
8bits.
The byte memory space on the ADSP-218xL series supports
read and write operations as well as four different data formats.
The byte memory uses data bits 15–8 for data. The byte mem-
ory uses data bits 23–16 and address bits 13–0 to create a 22-bit
address. This allows up to a 4 megabit
8 (32 megabit) ROM
or RAM to be used without glue logic. All byte memory accesses
are timed by the BMWAIT register.
Byte Memory DMA (BDMA, Full Memory Mode)
The byte memory DMA controller (Figure 11) allows loading
and storing of program instructions and data using the byte
memory space. The BDMA circuit is able to access the byte
memory space while the processor is operating normally and
steals only one DSP cycle per 8-, 16-, or 24-bit word transferred.
The BDMA circuit supports four different data formats that are
selected by the BTYPE register field. The appropriate number of
8-bit accesses are done from the byte memory space to build the
word size selected. Table 7 shows the data formats supported by
the BDMA circuit.
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address for
the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external byte
memory space. The 8-bit BMPAGE register specifies the start-
ing page for the external byte memory space. The BDIR register
field selects the direction of the transfer. Finally, the 14-bit
BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is gener-
ated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations. The source or destination
of a BDMA transfer is always on-chip program or data memory.
When the BWCOUNT register is written with a nonzero value
the BDMA circuit starts executing byte memory accesses with
wait states set by BMWAIT. These accesses continue until the
count reaches zero. When enough accesses have occurred to
Figure 9. Programmable Flag and Composite Control Register
Figure 10. System Control Register
BMWAIT
CMSSEL
0 = DISABLE
CMS
1 = ENABLE
CMS
DM(0x3FE6)
PFTYPE
0=INPUT
1=OUTPUT
(WHERE BIT: 11-IOM, 10-BM, 9-DM, 8-PM)
0
1
11
10
1
00
0
00
0
15 14 13 12 11 10
9
8
7
6
5
4321
0
PROGRAMMABLE FLAG AND COMPOSITE
SELECT CONTROL
RESERVED
RESERVED,ALW AYS
SE T TO 0
SP O RT0 ENABL E
0= DIS ABL E
1 = E NABL E
DM (0x3F FF)
S YSTEM CONTROL
S P ORT 1 E NABLE
0 = DISABLE
1 = E NABLE
S PO RT1 C ONF IGURE
0= FI,FO , IRQ0, IRQ1, S CLK
1= SP O RT1
DIS ABLE BMS
0 = E NABL E BMS
1= DIS AB LEBMS
PW AIT
P RO GRAM M E MOR Y
W AIT ST ATES
0
00
01
0
00
1
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
N OTE: RESERVED BITS ARE SHO WN O N A GRAY FIELD . THESE B ITS
SHOUL D ALW AYS BE WR ITTEN W ITH Z EROS.
R ESERVED
SE T T O 0
Figure 11. BDMA Control Register
Table 7. Data Formats
BTYPE
Internal Memory
Space
Word Size
Alignment
00
Program memory
24
Full word
01
Data memory
16
Full word
10
Data memory
8
MSBs
11
Data memory
8
LSBs
BDMA CONTROL
BMPAGE
BTYPE
BDIR
0= LOAD FROM BM
1= STORE TO BM
BCR
0 = RUN DURING BDMA
1 = HALT DURING BDMA
0
00
000
0
100
0
15 14 13 12 11 10
98
765
4
3
21
0
DM (0x3FE3)
BDMA
OVERLAY
BITS
(SEE TABLE 12)
相關PDF資料
PDF描述
GMM44DRTF CONN EDGECARD 88POS DIP .156 SLD
ECM12DSEN CONN EDGECARD 24POS .156 EYELET
ADSP-BF524KBCZ-3C2 IC DSP CTRLR 300MHZ 289CSPBGA
HMC35DRTS-S93 CONN EDGECARD 70POS DIP .100 SLD
TAJC474K050RNJ CAP TANT 0.47UF 50V 10% 2312
相關代理商/技術參數
參數描述
ADSP-2184LBSTZ-1602 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2184N 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2184NBCA-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:4K PM/4K DM RAM,16-BIT,80 MIPS, 1.8V - Bulk
ADSP-2184NBST-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 100-Pin LQFP
ADSP-2184NBSTZ-320 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤