- 您現在的位置：買賣IC網 > PDF目錄67357 > ADM1031ARQZ (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADM1031ARQZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 18/36頁 |
| 文件大?。?/td> | 596K |
| 代理商： | ADM1031ARQZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ADM1031
Rev. B | Page 25 of 36
FAN SPEED MEASUREMENT
The fan counter does not count the fan tach output pulses
directly, because the fan speed can be less than 1000 RPM and it
would take several seconds to accumulate a reasonably large
and accurate count. Instead, the period of the fan revolution is
measured by gating an on-chip 11.25 kHz oscillator into the
input of an 8-bit counter. The fan speed measuring circuit is
initialized on the rising edge of a PWM high output if fan speed
measurement is enabled (Bit 2 and Bit 3 of Configuration
Register 2 = 1). It then starts counting on the rising edge of the
second tach pulse and counts for two fan tach periods, until the
rising edge of the fourth tach pulse, or until the counter
overranges if the fan tach period is too long. The measurement
cycle repeats until monitoring is disabled. The fan speed
measurement is stored in the fan speed reading register at
address 0×08, 0×09.
The fan speed count is given by:
Count = (f × 60)/R × N
where:
f = 11.25 kHz
R = fan speed in RPM.
N = speed range (either 1, 2, 4, or 8)
The frequency of the oscillator can be adjusted to suit the
expected running speed of the fan by varying N, the speed
range. The oscillator frequency is set by Bit 7 and Bit 6 of Fan
Characteristics Register 1 (0×20) and Fan Characteristics
the fan measurements relate to the PWM_OUT pulse trains.
Table 15. Oscillator Frequencies
Bit 7
Bit 6
N
Oscillator Frequency (kHz)
0
1
11.25
0
1
2
5.625
1
0
4
2.812
1
8
1.406
CLOCK
CONFIG 2
REG. BIT 2
FAN
INPUT
START OF
MONITORING
CYCLE
FAN
MEASUREMENT
PERIOD
02402-
038
Figure 38. Fan Speed Measurement
In situations where different output drive circuits are used for
fan drive, it can be desirable to invert the PWM drive signal.
Setting Bit 3 of Configuration Register 1 (0×00) to 1, inverts the
PWM_OUT signal. This makes the PWM_OUT pin high for
100% duty cycle. Bit 3 of Configuration Register 1 should gener-
ally be set to 1 when using an n-MOS device to drive the fan.
If using a p-MOS device, Bit 3 of Configuration Register 1
should be cleared to 0.
FAN FAULTS
The FAN_FAULT output (Pin 8) is an active-low, open-drain
output used to signal fan failure to the system processor. Writing
a Logic 1 to Bit 4 of Configuration Register 1 (0×00) enables the
FAN_FAULToutput pin. The FAN_FAULT output is enabled by
default. The FAN_FAULT output asserts low only when five
consecutive interrupts are generated by the ADM1031 device due
to the fan running underspeed, or if the fan is completely stalled.
Note that the Fan Tach High Limit must be exceeded by at least
one before a FAN_FAULT can be generated. For example, if we
are only interested in getting a FAN_FAULT if the fan stalls, then
the fan speed value is 0×FF for a failed fan. Therefore, we should
make the Fan Tach High Limit = 0×FE to allow FAN_FAULT to
be asserted after five consecutive fan tach failures.
Figure 39 shows the relationship between INT, FAN_FAULT,
and the PWM drive channel. The PWM_OUT channel is
driving a fan at some PWM duty cycle, 50% for example, and
the fan’s tach signal (or fan current for a 2-wire fan) is being
monitored at the TACH/AIN pin. Tach pulses are being
generated by the fan, during the high time of the PWM duty
cycle train. The tach is pulled high during the off time of the
PWM train because the fan is connected high-side to the n-
MOS device.
Suppose the fan has twice previously failed its fan speed
measurement. Looking at Figure 39, PWM_OUT is brought high
for two seconds, to restart the fan if it has stalled. Sometime later
a third tach failure occurs. This is evident by the tach signal being
low during the high time of the PWM pulse, causing the fan
speed reading register to reach its maximum count of 255. Since
the tach limit has been exceeded, an interrupt is generated on the
INT pin. The fan fault bit (Bit 1) of Interrupt Status Register 1
(Register 0×02) is also asserted. Once the processor has
acknowledged the INT by reading the status register, the INT is
cleared. PWM_OUT is then brought high for another two
seconds to restart the fan. Subsequent fan failures cause INT to be
reasserted and the PWM_OUT signal is brought high for two
seconds (fan spin-up default) each time to restart the fan. Once
the fifth tach failure occurs, the failure is deemed to be
catastrophic and the FAN_FAULT pin is asserted low.
PWM_OUT is brought high to attempt to restart the fan. The
INT pin continues to generate interrupts after the assertion of
FAN_FAULT since tach measurement continues even after fan
failure. Should the fan recover from its failure condition, the
FAN_FAULT signal is negated, and the fan returns to its normal
operating speed.
Figure 40 shows a typical application circuit for the ADM1031.
Temperature monitoring can be based around a CPU diode or
discrete transistor measuring thermal hotspots. Either 2- or 3-
wire fans can be monitored by the ADM1031, as shown.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1031ARQ | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADRF6604ACPZ-R7 | 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
| ADRF6801ACPZ-R7 | 750 MHz - 1150 MHz RF/MICROWAVE I/Q DEMODULATOR |
| ADT14GS-REEL | ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.52V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT42GRT | ANALOG TEMP SENSOR-VOLTAGE, 0.75V, 3Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1031ARQZ-R7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQZ-REEL | 功能描述:板上安裝溫度傳感器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1031ARQZ-REEL7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1032 | 制造商:AD 制造商全稱:Analog Devices 功能描述:+-1C Remote and Local System Temperature Monitor |
| ADM1032_12 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1C Remote and Local System Temperature Monitor Supports SMBus Alert |
發布緊急采購，3分鐘左右您將得到回復。