- 您現在的位置：買賣IC網 > PDF目錄67357 > ADM1031ARQZ-R7 (ON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADM1031ARQZ-R7 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, QSOP-16 |
| 文件頁數： | 13/30頁 |
| 文件大?。?/td> | 299K |
| 代理商： | ADM1031ARQZ-R7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ADM1031
http://onsemi.com
20
Example 1:
If the desired value for RPM feedback mode is 5000 RPM,
the count to be programmed is:
Count = (f
× 60)/R × N
Since the desired RPM value, R, is 5000 RPM, the value
for count is:
N = 2:
Count = (11250
× 60)/5000 × 2
Count = 675000/10000
Count = 67 (assumes 2 tach pulses/rev)
Example 2:
If the desired value for RPM feedback mode is 3650 RPM,
the count to be programmed is:
Count = (f
× 60)/R × N
Since the desired RPM value, R, is 3650 RPM, the value
for count is:
N = 2:
Count = (11250
× 60)/3650 × 2
Count = 675000/7300
Count = 92 (assumes 2 tach pulses/rev)
Once the count value has been calculated, it should be
written to the fan tach high limit register. It should be noted
that in RPM feedback mode, there is no high limit register
for underspeed detection that can be programmed as there
are in the other fan speed control modes. The only time each
fan indicates a fan failure condition is whenever the count
reaches 255. Since the speed range N = 2, the fan fails if its
speed drops below 1324 RPM.
Programming RPM Values
1. Choose the RPM value to be programmed.
2. Set speed range value N = 2.
3. Calculate count value based on RPM and speed
range values chosen. Use the count equation to
calculate the count value.
4. Clear Bit 7 of Configuration Register 1 (Register
0
×00) to place the ADM1031 under software
control.
5. Write a 1 to Bit 5 of Configuration Register 1 to
place the device in RPM feedback mode.
6. Write the calculated count value to the fan tach
high limit register (Register 0
×10). The fan speed
now goes to the desired RPM value and maintains
that fan speed.
RPM Feedback Mode Limitations
RPM feedback mode only controls fan RPM over a limited
fan speed range of about 75% to 100%. However, this should
be enough range to overcome fanmanufacturing tolerance.
In practice, however, the program must not function at too
low an RPM value for the fan to run at, or the RPM mode does
not operate.
To find the lowest RPM value allowed for a given fan, do
the following:
1. Run the fan at 53% PWM duty cycle in software
mode. Clear Bit 5 and Bit 7 of Configuration
Register 1 (Register 0
×00) to enter PWM duty
cycle mode. Write 0
×08 to the fan speed
configuration register (Register 0
×22) to set the
PWM output to 53% duty cycle.
2. Measure the fan RPM. This represents the fan
RPM below which the RPM mode fails to operate.
Do not program a lower RPM than this value when
using RPM feedback mode.
3. Ensure that speed range N = 2 when using RPM
feedback mode.
Fan Drive and Speed Measurement
Fans come in a variety of different options. One
distinguishing feature of fans is the number of poles that a
fan has internally. The most common fans available have
four, six, or eight poles. The number of poles the fan has
generally affects the number of pulses per revolution the fan
outputs.
If the ADM1031 is used to drive fans other than 4pole
fans that output 2 tach pulses/revolution, then the fan speed
measurement equation needs to be adjusted to calculate and
display the correct fan speed, and also to program the correct
count value in RPM feedback mode.
Fan Speed Measurement Equations
For a 4pole fan (2 tach pulses/rev):
Fan RPM = (f
× 60)/Count × N
For a 6pole fan (3 tach pulses/rev):
Fan RPM = (f
× 60)/(Count × N × 1.5)
For an 8pole fan (4 tach pulses/rev):
Fan RPM = (f
× 60)/(Count × N × 2)
If in doubt as to the number of poles the fans used have,
or the number of tach output pulses/rev, consult the fan
manufacturer’s data sheet, or contact the fan vendor for
more information.
Fan Drive Using PWM Control
The external circuitry required to drive a fan using PWM
control is extremely simple. A single NMOS FET is the only
drive transistor required. The specifications of the MOSFET
depend on the maximum current required by the fan being
driven. Typical notebook fans draw a nominal 170 mA, and
so SOT devices can be used where board space is a
constraint. If driving several fans in parallel from a single
PWM output, or driving larger server fans, the MOSFET
needs to handle the higher current requirements. The only
other stipulation is that the MOSFET should have a gate
voltage drive, VGS <3.3 V, for direct interfacing to the
PWM_OUT pin. The MOSFET should also have a low
onresistance to ensure that there is not significant voltage
drop across the FET. This would reduce the maximum
operating speed of the fan.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1031ARQZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADM1031ARQZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADM1031ARQZ | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADM1031ARQ | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADRF6604ACPZ-R7 | 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1031ARQZ-REEL | 功能描述:板上安裝溫度傳感器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1031ARQZ-REEL7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1032 | 制造商:AD 制造商全稱:Analog Devices 功能描述:+-1C Remote and Local System Temperature Monitor |
| ADM1032_12 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1C Remote and Local System Temperature Monitor Supports SMBus Alert |
| ADM1032AR | 功能描述:IC TEMP MONITOR 85DEG C 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。