參數資料
型號： ADM1031ARQZ-R7
廠商： ON SEMICONDUCTOR
元件分類： 溫度/濕度傳感器
英文描述： DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
封裝： LEAD FREE, QSOP-16
文件頁數： 11/30頁
文件大?。?/td> 299K
代理商： ADM1031ARQZ-R7
ADM1031
http://onsemi.com
19
Programming the Filtered Automatic Fan Speed
Control Loop
1. Program a value for TMIN.
2. Program a value for the slope TRANGE.
3. TMAX = TMIN + TRANGE.
4. Program a value for fan spinup time.
5. Program the desired automatic fan speed control
mode behavior, that is, which temperature channel
controls the fan.
6. Program a ramp rate for the filtered mode.
7. Program the ADC sample rate in the fan filter
register.
8. Set Bit 0 to enable fan filtered mode for Fan 1.
9. Set Bit 1 to enable the fan filtered mode for Fan 2.
10. Select automatic fan speed control mode by setting
Bit 7 of Configuration Register 1.
PWM Duty Cycle Select Mode
The ADM1031 can operate under software control by
clearing Bit 7 of Configuration Register 1 (Register 0
×00).
This allows the user to directly control PWM duty cycle for
each fan.
Clearing Bit 5 and Bit 6 of Configuration Register 1
allows fan control by varying PWM duty cycle. Values of
duty cycle between 0% and 100% can be written to the fan
speed configuration register (0
×22) to control the speed of
each fan. Table 10 shows the relationship between hex
values written to the fan speed configuration register and
PWM duty cycle obtained.
Table 10. PWM Duty Cycle Select Mode
Hex Value
PWM Duty Cycle
00
0%
01
7%
02
14%
03
20%
04
27%
05
33%
06
40%
07
47%
08
53%
09
60%
0A
67%
0B
73%
0C
80%
0D
87%
0E
93%
0F
100%
Bits <3:0> set the PWM duty cycle for Fan 1; Bits <7:4>
set the PWM duty cycle for Fan 2.
RPM Feedback Mode
The second method of fan speed control under software is
RPM feedback mode. This involves programming the
desired fan RPM value to the device to set fan speed. The
advantages include a very tightly maintained fan RPM over
the fan’s life, and virtually no acoustic pollution due to fan
speed variation.
Fans typically have manufacturing tolerances of
±20%,
meaning a wide variation in speed for a typical batch of
identical fan models. If it is required that all fans run at
exactly 5000 RPM, it can be necessary to specify fans with
a nominal fan speed of 6250 RPM. However, many of these
fans run too fast and make excess noise. A fan with nominal
speed of 6250 RPM could run as fast as 7000 RPM at 100%
PWM duty cycle. RPM mode allows all of these fans to be
programmed to run at the desired RPM value.
Clearing Bit 7 of Configuration Register 1 (Register
0
×00) to 0 places the ADM1031 under software control.
Once under software control, the device can be placed into
RPM feedback mode by writing to Bit 5 and Bit 6 of
Configuration Register 1. Writing a 1 to Bit 5 and Bit 6
selects RPM feedback mode for each fan.
Once RPM feedback mode has been selected, the required
fan RPM can be written to the fan tach high limit registers
(0
×10, 0×11). The RPM feedback mode function allows a fan
RPM value to be programmed into the device, and the
ADM1031 maintains the selected RPM value by monitoring
the fan tach and speeding up the fan as necessary, should the
fan start to slow down. Conversely, should the fan start to
speed up due to aging, the RPM feedback slows the fan down
to maintain the correct RPM speed. The value to be
programmed into each fan tach high limit register is given by:
Count = (f
× 60)/R × N
where:
f = 11.25 kHz
R = desired RPM value
N = speed range; must be set to 2
The speed range, N, really determines what the slowest
fan speed measured can be before generating an interrupt.
The slowest fan speed is measured when the count value
reaches 255.
Since N = 2
Count = (f
× 60)/R × N
R = (f
× 60)/Count × N
R = (11250
× 60)/255 × 2
R = (675000)/510
R = 1324 RPM, fan fail detect speed
Programming RPM Values in RPM Feedback Mode
Rather than writing a value such as 5000 to a 16bit
register, an 8bit count value is programmed instead. The
count to be programmed is given by:
Count = (f
× 60)/R × N
where:
f = 11.25 kHz
R = desired RPM value
N = speed range 2
相關PDF資料
PDF描述
ADM1031ARQZ-REEL DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
ADM1031ARQZ-REEL7 DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
ADM1031ARQZ DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
ADM1031ARQ DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
ADRF6604ACPZ-R7 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER
相關代理商/技術參數
參數描述
ADM1031ARQZ-REEL 功能描述:板上安裝溫度傳感器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADM1031ARQZ-REEL7 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1032 制造商:AD 制造商全稱:Analog Devices 功能描述:+-1C Remote and Local System Temperature Monitor
ADM1032_12 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1C Remote and Local System Temperature Monitor Supports SMBus Alert
ADM1032AR 功能描述:IC TEMP MONITOR 85DEG C 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*