- 您現在的位置：買賣IC網 > PDF目錄378285 > ADC16061 (National Semiconductor Corporation) Self-Calibrating 16-Bit, 2.5 MSPS, 390 mW A/D Converter(16位2.5 MSPS,390 mW可自行校對的A/D轉換器) PDF資料下載
參數資料
| 型號： | ADC16061 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Self-Calibrating 16-Bit, 2.5 MSPS, 390 mW A/D Converter(16位2.5 MSPS,390 mW可自行校對的A/D轉換器) |
| 中文描述： | 自校準16位，250 MSPS的，390毫瓦的A / D轉換器（16位250 MSPS的，390毫瓦可自行校對的的A / D轉換器） |
| 文件頁數： | 14/20頁 |
| 文件大小： | 476K |
| 代理商： | ADC16061 |
Applications Information
(Continued)
The sign bit of the output word will be a logic low when V
+
is greater than V
. When V
+ is less than V
IN
, the sign
bit of the output word will be a logic high.
For single ended operation, one of the analog inputs should
be connected to V
. However, SNR and SINAD are re-
duced by about 12dB with a single ended input as compared
with differential inputs.
An input voltage of V
= (V
+) (V
) = 0 will be inter-
preted as mid-scale and will thus be converted to
0000,0000,0000,0000, plus any offset error.
The V
+ and the V
inputs of the ADC16061 consist of an
analog switch followed by a switched-capacitor amplifier.
The capacitance seen at the analog input pins changes with
the clock level, appearing as 12 pF when the clock is low,
and 28 pF when the clock is high. It is recommended that the
ADC16061 be driven with a low impedance source of 100
Ohms or less.
Since a dynamic capacitance is more difficult to drive than is
a fixed capacitance, choose driving amplifiers carefully. The
CLC440, LM6152, LM6154, LM6172, LM6181 and LM6182
are good amplifiers for driving the ADC16061.
Asimple application circuit is shown in Figure 6and Figure 7
Here we use two LM6172 dual amplifiers to provide a bal-
anced input to the ADC16061. Note that better noise perfor-
mance is achieved when V
+
voltage is forced with a
well-bypassed resistive divider. The resulting offset and off-
set drift is minimal.
1.4 V
CM
Analog Inputs
The V
CM
input of the ADC16061 is internally biased to 40%
of the V
A
supply with on-chip resistors, as shown in Figure 5
The V
pin must be bypassed to prevent any power supply
noise from modulating this voltage. Modulation of the V
potential will result in the introduction of noise into the input
signal. The advantage of simply bypassing V
(without
driving it) is the circuit simplicity. On the other hand, if the V
A
supply can vary for any reason, V
will also vary at a rate
and amplitude related to the RC filter created by the bypass
capacitor and the internal divider resistors. However, perfor-
mance of this approach will be adequate for many
applications.
By forcing V
CM
to a fixed potential, you can avoid the prob-
lems mentioned above. One such approach is to buffer the
2.0 Volt reference voltage to drive the V
input, holding it at
a constant potential as shown in Figure 6and Figure 8 If the
reference voltage is different from the desired V
, that
desired V
voltage may be derived from the reference or
from another stable source.
Note that the buffer used for this purpose should be a slow,
low noise amplifier. The LMC660, LMC662, LMC272 and
LMC7101 are good choices for driving the V
CM
pin of the
ADC16061.
If it is desired to use a multiplexer at the analog input, that
multiplexer should be switched at the rising edge of the clock
signal.
2.0 DIGITAL INPUTS
Digital Inputs consist of CLOCK, RESET, CAL, RD and PD.
All digital input pins should remain stable from the fall of the
clock until 30ns after the fall of the clock to minimize digital
noise corruption of the input signal on the die.
2.1 The CLOCK
signal drives an internal phase delay loop to
create timing for theADC. Drive the clock input with a stable,
low phase jitter clock signal in the range of 300 kHz to 2.5
MHz. The trace carrying the clock signal should be as short
as possible. This trace should not cross any other signal line,
analog or digital, not even at 90.
The CLOCK signal also drives the internal state machine. If
the clock is interrupted, the data within the pipeline could
become corrupted.
A 100 Ohm damping resistor should be placed in series with
the CLOCK pin to prevent signal undershoot at that input.
2.2 The RESET
input is level sensitive and must be pulsed
high for at least two clock cycles to reset the ADC after
power-up and before calibration (See Timing Diagram 2).
2.3 The CAL
input is level sensitive and must be pulsed high
for at least two clock cycles to begin ADC calibration (See
Timing Diagram 2). Reset the ADC16061 before calibrating.
Re-calibrate after the temperature has changed by more
than 50C since the last calibration was performed and after
return from power down.
During calibration, use the same clock frequency that will be
used for conversions to avoid excessive offset errors.
Calibration takes 272,800 clock cycles. Irrelevant data may
appear at the data outputs during RESET or CAL and for 13
clock cycles thereafter. Calibration should not be started until
the reference outputs have settled (100ms with 1μF capaci-
tors on these outputs) after power up or coming out of the
power down mode.
2.4 RD
pin is used to READ the conversion data. When the
RD pin is low, the output buffers go into the active state.
When the RD input is high, the output buffers are in the high
impedance state.
2.5 The PD
pin, when low, holds the ADC16061 in a
power-down mode where power consumption is typically
less than 2mW to conserve power when the converter is not
being used. Power consumption during shut-down is not
affected by the clock frequency, or by whether there is a
clock signal present. The data in the pipeline is corrupted
while in the power down mode. The ADC16061 should be
reset and calibrated upon returning to normal operation after
a power down.
3.0 OUTPUTS
The ADC16061 has four analog outputs: V
REF
+
V
, V
and V
. There are 17 digital out-
puts: EOC (End of Conversion) and 16 Data Output pins.
3.1 The reference output voltages
are made available only
for the purpose of bypassing with capacitors. These pins
should not be loaded with more than 10 μADC. These output
voltages are described as
V
REF
+
OUT
= V
CM
+
1
2
V
REF
OUT
,
DS100889-21
FIGURE 5. V
input to the ADC16061 V
is set to
40% of V
A
with on-chip resistors. Performance is
improved when V
CM
is driven with a stable, low
impedance source
A
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| ADC16071 | 16-Bit Delta-Sigma 192 ks/s Analog-to-Digital Converters |
| ADC16471 | 16-Bit Delta-Sigma 192 ks/s Analog-to-Digital Converters |
| ADC16071CIN | 16-Bit Delta-Sigma 192 ks/s Analog-to-Digital Converters |
| ADC16471CIWM | 16-Bit Delta-Sigma 192 ks/s Analog-to-Digital Converters |
| ADC16471CIN | SBS-Compliant Gas Gauge for Use with bq29311 38-TSSOP -20 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC16061CCVT/NOPB | 功能描述:IC ADC 16BIT 2.5MSPS 52LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| ADC1610S065F1/DB,598 | 功能描述:數據轉換 IC 開發工具 ADC DEMO BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADC1610S065F2/DB,598 | 功能描述:數據轉換 IC 開發工具 ADC DEMO BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADC1610S065HN/C1,5 | 功能描述:模數轉換器 - ADC SNGLE 16b ADC 65MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC1610S065HN/C1;5 | 功能描述:模數轉換器 - ADC SGL 16b ADC 65 MSPS CMOS OR LVDS DDR RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。