參數資料
型號： ADAU1446YSTZ-3A-RL
廠商： Analog Devices Inc
文件頁數： 77/92頁
文件大?。?/td> 0K
描述： IC SIGMADSP 175MHZ 100LQFP
標準包裝： 1,000
系列： SigmaDSP®
類型： 音頻處理器
應用： 車載音頻
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（16x16）
包裝： 帶卷 (TR)
ADAU1445/ADAU1446
Rev. A | Page 79 of 92
SOFTWARE FEATURES
SOFTWARE SAFELOAD
To update parameters in real time while avoiding pop and click
noises on the output, the ADAU1445/ADAU1446 use a software
safeload mechanism. SigmaStudio sets up the necessary code
and parameters automatically for new projects. The safeload code,
along with other initialization code, fills the first 36 locations
in program RAM. The first eight parameter RAM locations
(Address 0x0000 to Address 0x0007) are configured by default
in SigmaStudio as described in Table 78.
Table 78. Software Safeload Parameter RAM Defaults
Address
(Hex)
Function
0x0000
Modulo RAM size
0x0001
Safeload Data 1
0x0002
Safeload Data 2
0x0003
Safeload Data 3
0x0004
Safeload Data 4
0x0005
Safeload Data 5
0x0006
Safeload target address (offset of 1)
0x0007
Number of words to write/safeload trigger
Address 0x0000, which controls the modulo RAM size, is set by
SigmaStudio and is based on the dynamic address generator
mode of the project.
Address 0x0001 to Address 0x0005 are the five data slots for storing
the safeload data. The safeload parameter space contains five data
slots by default because most standard signal processing algorithms
have five parameters or fewer.
Address 0x0006 is the target address in parameter RAM (with
an offset of 1). This designates the first address to be written.
If more than one word is written, the address increments
automatically for each data-word. The reason for the target
address offset of 1 is that the write address is calculated relative to
the address of the data, which starts at Address 0x0001. Therefore,
if the intention is to update a parameter at Address 0x000A, the
target address should be 0x0009.
Address 0x0007 designates the number of words to be written.
For a biquad filter, the number is five. For a simple monogain
cell, the number is one. This address also serves as the trigger;
when it is written, a safeload write is triggered on the next frame.
The safeload mechanism is software based and executes once
per audio frame. Therefore, system designers should take care
when designing the communication protocol. A delay equal to
or greater than the sampling period (the inverse of sampling
frequency) is required between each safeload write. At a sample
rate of 48 kHz, this equates to a delay of greater than or equal to
20.83 μs. If this delay is not observed, the downloaded data will
be corrupted.
SOFTWARE SLEW
When the values of signal processing parameters are changed
abruptly in real time, they sometimes cause pop and click sounds
to appear on the audio outputs. To avoid this, some algorithms
in SigmaStudio implement a software slew functionality. Software
slew algorithms set a target value for the parameter and contin-
uously update the parameter’s value until it reaches the target.
The target value takes an additional space in parameter RAM, and
the current value of the parameter is updated in the nonmodulo
section of data RAM. Assignment of parameters and nonmodulo
data RAM is handled by the SigmaStudio compiler and does not
need to be programmed manually.
Slew parameters can follow several different curves, including an
RC-type curve and a linear curve. These curve types are coded
into each algorithm and cannot be modified by the user.
Because algorithms that use software slew generally require more
RAM than their nonslew equivalents, they should be used only
in situations in which a parameter will change during operation
of the device.
Figure 59 shows an example of a volume slew applied to a sine wave.
INITIAL VALUE
NEW TARGET
VALUE
SLEW
CURVE
0
76
96
-0
65
Figure 59. Example of Volume Slew
相關PDF資料
PDF描述
SP3243EUCA-L/TR IC TXRX RS232 INTELLIGENT 28SSOP
SP3232EUEA-L IC TXRX RS232 ESD 16SSOP
AD7856ARSZ-REEL7 IC ADC 14BIT 8CHAN 5V 24SSOP
VI-21J-IU-F3 CONVERTER MOD DC/DC 36V 200W
CS8416-CNZ IC RCVR DGTL 192KHZ 28QFN COMM
相關代理商/技術參數
參數描述
ADAU1450WBCPZ 功能描述:IC AUDIO PROCESSOR 72LFCSP 制造商:analog devices inc. 系列:SigmaDSP? 包裝:托盤 零件狀態:有效 類型:Sigma 接口:I2C，SPI 時鐘速率:147.456MHz 非易失性存儲器:- 片載 RAM:64KB 電壓 - I/O:3.3V 電壓 - 內核:1.20V 工作溫度:-40°C ~ 105°C（TA） 安裝類型:表面貼裝 封裝/外殼:72-VFQFN 裸露焊盤，CSP 供應商器件封裝:72-LFCSP-VQ（10x10） 標準包裝:1
ADAU1450WBCPZ-RL 功能描述:IC AUDIO PROCESSOR 72LFCSP 制造商:analog devices inc. 系列:SigmaDSP? 包裝:剪切帶（CT） 零件狀態:在售 類型:Sigma 接口:I2C，SPI 時鐘速率:147.456MHz 非易失性存儲器:- 片載 RAM:64KB 電壓 - I/O:3.30V 電壓 - 內核:1.20V 工作溫度:-40°C ~ 105°C（TA） 安裝類型:表面貼裝 封裝/外殼:72-VFQFN 裸露焊盤，CSP 供應商器件封裝:72-LFCSP-VQ（10x10） 標準包裝:1
ADAU1451WBCPZ 功能描述:IC AUDIO PROCESSOR 72LFCSP 制造商:analog devices inc. 系列:SigmaDSP? 包裝:托盤 零件狀態:有效 類型:Sigma 接口:I2C，SPI 時鐘速率:294.912MHz 非易失性存儲器:- 片載 RAM:96kB 電壓 - I/O:3.3V 電壓 - 內核:1.20V 工作溫度:-40°C ~ 105°C（TA） 安裝類型:表面貼裝 封裝/外殼:72-VFQFN 裸露焊盤，CSP 供應商器件封裝:72-LFCSP-VQ（10x10） 標準包裝:1
ADAU1451WBCPZ-RL 功能描述:IC AUDIO PROCESSOR 72LFCSP 制造商:analog devices inc. 系列:SigmaDSP? 包裝:剪切帶（CT） 零件狀態:在售 類型:Sigma 接口:I2C，SPI 時鐘速率:294.912MHz 非易失性存儲器:- 片載 RAM:96kB 電壓 - I/O:3.30V 電壓 - 內核:1.20V 工作溫度:-40°C ~ 105°C（TA） 安裝類型:表面貼裝 封裝/外殼:72-VFQFN 裸露焊盤，CSP 供應商器件封裝:72-LFCSP-VQ（10x10） 標準包裝:1
ADAU1452WBCPZ 功能描述:IC AUDIO PROCESSOR 72LFCSP 制造商:analog devices inc. 系列:SigmaDSP? 包裝:托盤 零件狀態:有效 類型:Sigma 接口:I2C，SPI 時鐘速率:294.912MHz 非易失性存儲器:- 片載 RAM:192kB 電壓 - I/O:3.3V 電壓 - 內核:1.20V 工作溫度:-40°C ~ 105°C（TA） 安裝類型:表面貼裝 封裝/外殼:72-VFQFN 裸露焊盤，CSP 供應商器件封裝:72-LFCSP-VQ（10x10） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*